with the letter L or coloured red.
When making the electrical connections,
check that the current socket has a ground
connection and that the voltage values
correspond to those indicated on the data
plate inside the appliance itself.
In case your appliance is not furnished with
a non separating flexible cable and has no
plug, or has not got any other device ensu-
ring omnipolar disconnection from the elec-
tricity main, with a contact opening distance
of at least 3 mm, such separating device
ensuring disconnection from the main must
be included in the fixed installation. If your
unit features a power lead and plug, position
this so the plug is accessible.
Always switch off the electricity supply be-
fore carrying out any cleaning or servicing
operations on the appliance.
USE
-----------------------------------------------------
Avoid using materials which could cause
spurts of flame (flambées) near the ap-
pliance.
When frying, take particular care to prevent
oil and grease from catching fire. Already
used oil is especially dangerous in this re-
spect. Do not use uncovered electric grates.
To avoid possible risks of fire always comply
with the indicated instructions when cleaning
grease filters and when removing grease
deposits from the appliance.
MAINTENANCE
-----------------------------------------------------
Thorough servicing guarantees correct and
long-lasting operation.
The grease filters need particular care.
Fig. 4: The grease filters must be cleaned
about every 30 hours of operation (all the
LEDs flash simultaneously). To remove the
filters: open the door pulling it forwards and
remove the filters pushing the catch upwards
in correspondence to the handle. Wash the
filters with a neutral detergent by hand or in
a dish washer. When the clean filters have
been remounted, press one of the three
speed buttons to restart the counter.
Any fat deposits should be removed from the
appliance periodically depending on amount
of use (at least every 2 months). Avoid using
abrasive or corrosive products. To clean
painted appliances on the outside, use a cloth
dipped in lukewarm water and neutral
detergent. To clean the inside of the
appliance, use a cloth (or brush) dipped in
denatured ethyl alcohol.
DESCRIPTION
-----------------------------------------------------
The hood comes in a filtering or ducting version.
With the filtering version (Fig. 1) the air and
steam conveyed by the hood are purified by the
charcoal filters and recirculated in the room.
With the ducting version (Fig. 2) the steam and
kitchen smells are conveyed directly to the outside
through a disposal duct fitted in the wall/ceiling.
Therefore, use of charcoal filters are not
necessary.
INSTALLATION
-----------------------------------------------------
To facilitate installation, remove the grease
filters and disassemble the front door.
Door disassembly: open the door by pulling
it forwards; operating on the inside of the hood
remove the 2 screws D as illustrated in Fig. 3.
Hold the tab L down and remove the door from
the guides.
Grease filters disassembly: open the door
pulling it forwards; in correspondence to the
handle, push the catch upwards and extract the
filter (Fig. 4).
Essential requirements for assembly: – set
up the electrical connection. – if your hood is to
be installed in the ducting version, prepare the
air evacuation opening.
Before installing the hood, the following opera-
tions must be carried out:
- Fig. 5: Fit the flange to the hood using 2 screws
(provided).
Fig. 6: check that the brackets L are
mounted on the hood; if not, fix them using 2
metrical screws (V) with washers (all provided);
also check that the 2 metric screws (M) are fit-
ted. Bearing in mind that the distance between
the hood and the hob must be at least 65 cm, fix
the 2 brackets S (provided) to the wall using the
screws and screw anchors provided – see Fig. 7.
Hook the hood to the 2 brackets; for alignment
with the wall or kitchen units, the hood may be
adjusted in height by turning the screws M, and
in depth by turning the screws V (Fig. 7). Before
tightening all the screws, check the distance
between the hood and the wall; if necessary, use
the spacer provided.
Fitting the spacer: cut the spacer to the
