background image

16

TECHNICAL ASSISTANCE AND SPARES

Before leaving the factory, this appliance was tested and regulated by specially qualified experts in order to

guarantee the best operating results. 

The original spare parts can be found only in our Technical Assistance Centres and authorised shops.

Every repair or regulation operation which should become subsequently necessary must be carried out with

the utmost care and attention by qualified personnel. 

This is why we recommend that you always contact the Dealer who sold the appliance or our nearest

Assistance Centre, specifying the brand, the model, the serial number and the type of problem affecting your

appliance. The pertinent data is stamped on the label applied to the underside of the appliance and on the

label applied to the packing box.

This information enables the technical assistance department to acquire the appropriate spare parts and

consequently guarantee prompt and targeted intervention.  We recommend that you write this data in the

spaces below and keep it to hand at all times:

BRAND: .........................................................

MODEL: .........................................................

SERIES: .........................................................

All manuals and user guides at all-guides.com

all-guides.com

Содержание GKS 11742.0-35 F-UL


















Отзывы: