background image

C. 

INSTALLATION OF ATV TONGUE ASSEMBLY  

(if the lawn and garden hitching was purchased 

refer to Section B. Installation of Lawn & Garden Hitching)

 

1.  The tongue can be installed either on the left or right caster assembly depending on how the 

wing mower will be towed.  

See figure 4.

  

Secure the hitch pivot on the chosen caster 

assembly with the 3/8” x 2-1/2” hex head bolt, lock washer, and nut provided. 

2.  Install the tongue into the hitch pivot and secure by placing a 5/16” wire lock pin on each side 

of the hitch pivot. 

 
D.  

INSTALLATION OF OPTIONAL HITCHES 

1.  When a long tongue is needed, remove the tongue pivot angles and spacer from the tongue 

assembly and attach to the tongue extension.  

See figure 5.

  Slip the tongue in between the 

two flats on the tongue extension and secure with 3/8” x 2-1/2” hex head bolts, lock washers, 
and nuts provided. 

2.  When a second mower is pulled behind the first mower in tandem, then the rear hitch can be 

installed on the left rear axle assembly.  

See figure 5.

  Secure with 3/8” x 3-1/4” hex head 

bolts, lock washers, and nuts provided. 

 

Note:

 The long tongue extension (Part # 900008) and rear hitch assembly (Part # 900009) must 

be ordered separately. 

 

Long Tongue Extension 

Tongue Pivot Angle 

Spacer 

Short Tongue 

Rear Hitch Assembly 
Attach to Left Rear Axle 

Figure 5:  Long Tongue Assembly and Rear Hitch Assembly 

 

OPERATIONS AND ADJUSTMENTS 

 

This safety alert symbol is used to indicate safety instructions.  Follow 
these instructions to avoid personal injury and/or property damage.  Read 
and follow all instructions in this manual and the included engine manual. 

 

 

WARNING:

  Do not allow anyone to operate this equipment who has not fully read and 

comprehended  the safety manual and who has not been properly trained in the safe 
operation of the equipment.

 

 

WARNING:

  Operator should be familiar with all functions of the unit. 

 

8

Содержание AcrEase C60K































Отзывы: