.BHOFUJD-PDBUJPO
The first hole of
Gear S3 strap
Built-in Wireless
Charging Pad
Buckle
Gear S3
Screw
(Silver)
g
c
Check the LED lighting
on the Security sensor
c
Cradle
head
Cable
direction
Cable
direction
Protective
film
Remove
a
e
f
Cutting
a
Control box
Control box
▶
Safety warning
▶
How to separate the Security sensor
▶
Information
※
The specifications and design of the product may be modified without prior
notice for the improvement of product performance.
Do not expose the product to fire or other electric heaters!
- There is a danger of fire or damage to the product.
Do not disassemble, repair, or remodel the product!
- There is a danger of injury.
- Please call the service center when repair is necessary.
Do not forcefully bend or pull the wire!
- There is a danger of damage to the product or injury to the user.
When the wire is disconnected or breaks away, do not touch the wire with bare hands,
but always wear protective hand gloves!
- The disconnected part of the wire is sharp, thus, may cause injury.
Do not use the wire for purposes other than as a security alarm device, and do not allow
access to children!
- Winding the wire around your neck or body may result in death or serious injury.
Do not touch the wire when there is lightning and thunder!
- There is a danger of electric shock.
Warning: To prevent the injury of the user or other people and property damage,
the following instructions must be followed.
*In case of user’s fault during the warranty period it is not free of charge.
Warranty Period
Item
One-year
Manufacturer
KUMOH Electronics Co.,Ltd
Address
35, Gilju-ro 444beon-gil, Wonmi-gu,
Bucheon-si, Gyeonggi-do (Seoul 14556 Korea)
82-32-662-9312
82-32-662-2000
■
Limited warranty
■
Manufacturer Information
Tel
Fax
Gear S3 frontier/classic
Normal Security Set
Turn off the Control box, separate the security cable connector( ), and loosen
the black screw( ) assembled to the Security sensor.
※
If you separate the connector( ) without turning off the Control box, an alarm
will occur.
1
Separate the Security sensor( ) and assemble the screw(silver) for Gear S3.
※
Make sure to use the screw(silver) separated from Gear S3 before installing the
Security sensor. If the screw(black) for installing the Security sensor is used,
it will not be assembled normally.
2
※
Before separating the Security sensor, make sure to turn off the Control box.
6
When mounting Gear S3 on the cradle head, check if the cable of the Security sensor( )
is installed correctly to direction of the rear side of the cradle as shown in the figure below.
※
If the Security sensor is installed in the wrong direction, install it again by checking
the assembling direction in of the installation guide.
Install the buckle in
the first hole of Gear S3 strap
as below figure, and put the
device on the center of cradle head.
※
Make sure that the buckle should be installed in the first hole of strap.
※
The wireless charger and the magnet are built in cradle head.
5
g
c
a
a
a
The coil for wireless charging function and magnetic to places the Gear S3 in right charging point are built in head of security cradle.
When put the Gear S3 onto cradle, the magnetic power guides the device to center of cradle. If it is set apart from center, the charging will not Working.
3
Auto adjustment head by magnet
8
Assemble the security cable( ) temporarily using the cable tie( ) and the cable
tie mount( ). Remove the protective film from the double-sided table on the
bottom surface of the cable tie mount, attach the cable tie mount( ) firmly on
the proper position on the table, pull and tighten up the table tie( ) completely
and cut off any excess part.
After finishing the installation, connect the security cable connector( ) to the
Control box and turn on the power. If the power supply is connected normally,
LED on the Security sensor will turn on.
7
a
e
e
f
f
a
a
c
Press and hold evenly
for 30 seconds or more!
Magnetic power
set the Gear S3
to locate the
charging point.
