TA112MX3-E - 3 / 18 - 07-01-25
F
UNCTIONS
The following functions are implemented:
−
Start-stop for diesel and gas engine with checking of preliminary start-enable conditions,
−
Monitor for generator voltage, frequency and rotating field (asymmetry),
−
Generator current monitor: Over-current, short-circuit, unbalanced currents and thermal overload (bimetal
relay),
−
44 alarm signals, 19 of them can be configured by the customer (text and triggering),
−
Battery monitor and two analogue inputs for direct connection of VDO sensors,
−
Two alarms are possible for each analogue input,
−
Potential-free analogue output for direct actuation of a speed controller,
−
Parameterisation via optical fibre or directly via the keys and the display.
B
ASIC
O
PERATION OF THE
C
ONTROL
U
NIT
The control unit is simple to operate by the push buttons and without menu navigation as all previous
KUHSE models. The operation mode is selected via four keys. In M
ANUAL
and T
EST
modes, the generator
supply is executed using the buttons that are arranged in the mimic diagram.
The S
TART
button can be used for a manual start in M
ANUAL
mode. The LED T
EST
and A
LARM
O
FF
buttons
are self-explanatory.
In normal operation, the display must only be used for showing current alarms and actual values. The menu
is easy to use: select the required group (alarms or actual values) with the [
→
] and [
←
]
buttons, then view
the required actual value or current alarm with the [
↑
] and [
↓
] buttons.
O
PERATION OF THE
D
ISPLAY
Values or parameters are selected, as you would read a book. The further down listed groups are arranged as
'pages'. You can scroll forwards and backwards through these groups by pressing the [
→
] and [
←
]
keys. The
entries of each group can be read from top to bottom like lines of a text. Select a line by pressing the keys [
↓
]
(down) and [
↑
] (up). The selection starts again with the other end of the 'page', when the top or bottom of the
'page' is reached.
Hold down the LED T
EST
button and press [
←
] to select directly the A
CTUAL
V
ALUES
group, hold down
LED T
EST
and press [
→
] to display the group C
URRENT
A
LARMS
.
To modify a parameter, first enter the relevant I
DENT
-N
UMBER
. However, parameters of group 0, -
GENERAL
P
ARAMETERS
-, can be modified without entering this number. Parameters are modified as follows:
1. Select the required parameter group with the [
←
] and [
→
] buttons. One or two parameters are displayed.
2. Press O
FF
and LED T
EST
(function: P
ARA ON
or P
ARA OFF
) together. This opens parameterisation mode
as can be seen by the specific cursor [
█
]. The selection of the group cannot be changed now.
3. Select the required parameter line (if two are displayed) with the [
↓
] and [
↑
] buttons.
4. Press O
FF
and A
LARM OFF
(E
NTER
function) together to select the parameter line. The shape of the cursor
confirms the selection, as it underscores (e.g.
1
9
6
) now the part of the parameter that is to be modified.
The chosen parameter cannot be deselected now.
5. Select the figure or letter of the parameter that you want to modify with the [
←
] and [
→
] cursor keys.
Numerical parameters can be increased or decreased by increments of 1 with the [
↑
] and [
↓
] buttons.
Press the same buttons to negate parameters that are displayed with a letter (+/- signs, alarm coding etc.).
6. Press O
FF
and A
LARM OFF
together to store the displayed parameter. Press O
FF
and LED T
EST
instead of
O
FF
and A
LARM OFF
to abort parameterisation.
Display contrast setting
Hold down LED T
EST
and press key [
↑
] to increase the display contrast (makes the display darker) or LED
T
EST
and key [
↓
] to lower it (makes the display lighter).
Changes without further notice reserved.
