KUHN FC 4000 RG Скачать руководство пользователя страница 47

Страница: 47 / 80

Instructions for work

Mower conditioner

FC4000RG

3. Machine use

Before the machine engages the crop:

- Engage the tractor PTO and slowly increase the

speed up to 1000 min

-1

Groundspeed

Before mowing and to reduce risks of
projections, lower side guards and front
guard.

Check that nobody is within the machine
pivoting area.

Keep all persons and animals away from the
machine danger zone.

Never lean or step on the guards.

In case an obstacle has been struck, check
that the mowing unit has not been damaged.

Use hand throttle to prevent the conditioner from
getting jammed due to a drop in rotational speed.

The machine is lifted from working position into
headland turn position by means of the mowing
unit lift cylinders

Adapt the forward speed to the working
conditions.

Содержание FC 4000 RG

















































































Результаты поиска

Содержание FC 4000 RG

Отзывы:

Похожие инструкции для FC 4000 RG

Бренды по названию

Популярные бренды

KUHN FC 4000 RG, Руководство оператора

Результаты поиска

Содержание FC 4000 RG

Отзывы:

Похожие инструкции для FC 4000 RG

Бренды по названию

Популярные бренды