KUHN ALTOR 4560 Скачать руководство пользователя страница 89

Страница: 89 / 98

Maintenance and storage

Silo unloader - Straw Spreader

ALTOR 4560

10. Storage

If the machine is not to be used for a long period, prepare

it for storage:

- Clean the body (inside, outside and underside).

- Remove any product build-up.
- Repaint any surface in danger of rusting with a special

paint.

- Grease the underbody.
- Push the cylinder rods in to the maximum to protect

them from humidity and dust.

- Clean all the greasing points and joints and grease

them.

- Park the machine under a shelter on blocks to isolate

it from damp ground.

- Check the tire pressure and that the studs are

tightened.

- Check that the conveyor is slack.

Do not clean the cylinder rods with a
pressurized washer and detergent.

Do not direct a pressurized jet of water
towards a cylinder rod scraper seal.

Grease the cylinder rods in contact with the
outside every month.

Содержание ALTOR 4560



































































































Результаты поиска

Содержание ALTOR 4560

Отзывы:

Бренды по названию

Популярные бренды

KUHN ALTOR 4560, Руководство оператора

Результаты поиска

Содержание ALTOR 4560

Отзывы:

Бренды по названию

Популярные бренды