manualshive.com logo in svg

Kubota VS 220, Руководство пользователя

Поделиться
Скачать
Kubota VS 220 Скачать руководство пользователя страница 127

Maintenance

127

Lubricate with oil 

and grease

Never use more oil or grease than prescribed

A too high oil level may result in an overheated machine and damaged 

seals.

Waste storage and disposal

Waste  from  performing  maintenance  on  the  machine  could  be 

contaminated  with  fertiliser,  oil  and  grease.  Collect  the  waste  and 

dispose of it in terms of national regulations.

Coupling shaft

All  lubricating  nipples  of  the  coupling  shaft  can  be  filled  with  a 

universal grease type.

See the paragraph above »Lubricate with oil and grease«.

See paragraph »Maintenance intervals« on page 126.

Coupling shaft with 

quick lock

Lubricate the 4 nipples.

Check the condition of the protection sleeves and the check 

chains.

Replace them if damaged.

Tractor side quick lock

Lubricate with oil the slider of the coupling on the tractor side.

Coupling shaft profiled 

tubes

Grease the contact surfaces of the two profiled tubes.

Detach the coupling shaft on the one side.

Pull the shaft halves away from each another.

Grease the running surface of the inner profiled tube.

Slide the shaft halves into each other.

Attach the coupling shaft.

Hook the check chains to the tractor side.

Part / action

Quantity

Specifications

Lubricate with grease

1 to 2 times

 Kubota Polyurea grease or equivalent

Lubricate with oil

SAE 80W-90 MIL-L-2105C

4 grease nipples

Greasing

Содержание VS 220



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды