Kubota K008-5 Скачать руководство пользователя страница 58

Страница: 58 / 168

W9215-8135-1

06/2021

Assembly and functions

Controls U10-5

The controls includes the following components:

Left control lever

Left drive lever

Right drive lever

Right control lever

Dozer control lever

Boom swing pedal

Control lever lock (not shown)

Auxiliary port pedal

Throttle lever

10. Selector lever for the dozer/extendable track width

Description of the controls

Left control lever

The left control lever is used to swivel the swivel frame and move the arm. See the table below for details.

The figure shows, in connection with the following table, the
functions of the left and right control levers.

Left drive lever

With the drive levers the excavator can be driven forwards and backwards and also turned. The left drive lever
controls the left track.

Right drive lever

With the drive levers the excavator can be driven forwards and backwards and also turned. The right drive
lever controls the right track.

Control levers

Movement

Right control lever

1
2
3
4

Lower boom
Raise boom
Bucket crowd
Bucket dump

Left control lever

A
B
C
D

Arm dump
Arm crowd
Swivel frame to the left
Swivel frame to the right

Содержание K008-5









































































































































































Результаты поиска

Содержание K008-5

Отзывы:

Бренды по названию

Популярные бренды

Kubota K008-5, Руководство по эксплуатации

Результаты поиска

Содержание K008-5

Отзывы:

Бренды по названию

Популярные бренды