Kubota K008-5 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 168

Kubota K008-5 Скачать руководство пользователя страница 57

Assembly and functions

W9215-8135-1

55

06/2021

Displays and indicators - description

Fuel level indicator

The fuel level indicator lights up when there are only 2 l of fuel left in the fuel tank.
The machine can keep working for about 1 hour after it lights up. However, if you continue to use it, the ma-
chine may suddenly stop and cause danger. It's recommended to refuel immediately.

Engine oil pressure indicator

The indicator lights up when the starter switch is switched to the RUN position. It also lights up when the en-
gine oil pressure drops considerably and upon stopping the engine.

Charge lamp

The indicator lights up when the starter switch is switched to the RUN position. The charge lamp goes off as
soon as the engine has started.

The time meter indicates in intervals of 0.1 hours (i.e. 6 minutes) the hours of operation of the machine.

Coolant temperature indicator

The warning lamp lights up when the temperature of the coolant lies outside of the normal range.

Controls K008-5

The controls includes the following components:

1.

Left control lever

2.

Left drive lever

3.

Right drive lever

4.

Right control lever

5.

Dozer control lever

6.

Boom swing pedal

7.

Control lever lock

8.

Auxiliary port pedal

9.

Throttle lever

10. Selector lever for the dozer/extendable track width

The time meter even continues when the engine has stopped but the starter switch is still in the RUN

position

1

2

3

4

5

7

6

8

9

7

10

«
...
55
56
57
58
59
...
»

Содержание K008-5









































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды