Kubota K-Hitch AP-KH15 Скачать руководство пользователя страница 15

Страница: 15 / 32

Section 1: Assembly & Set-up

AP-KH15 K-Hitch® 320-135MK

9/21/22

Table of Contents

Tractor Requirements

Tractor horsepower should be within the range noted

below. Tractors outside the horsepower range must not

be used.

3-Point Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . Cat. I
Tractor . . . . . . . . . . . . . . . . . Kubota B01 & LX Series

WARNING

To prevent serious injury or death:
Lightweight tractors with rear attached implements may need

weights added to the front to maintain steering control.

Consult your tractor Operator’s Manual to determine weight

requirements and maximum limitations.

Common Bolt Torque Values

Refer to

“Torque Values Chart”

on page 25 to determine

correct torque values when tightening hardware.

Before You Start

WARNING

To avoid serious injury or death:
Allow only persons to operate this implement who have fully

read and comprehended this manual, and who have been

properly trained in the safe operation of this implement.

Serious injury or death can result from the inability to read,

understand, and follow instructions provided in this manual.

This K-Hitch is shipped fully assembled from the factory.

Some preparation will be necessary to attach the

implement to the customer’s tractor. Make sure the

intended tractor conforms to

“Tractor Requirements”

above.
Go through the

“Pre-Assembly Checklist”

on this page

before attaching the K-Hitch to a tractor. To make the job

safer, have all needed parts and equipment readily at

hand.

Section 1: Assembly & Set-up

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures.

Follow these procedures and any additional shutdown

procedures provided in your tractor Operator’s Manual

before leaving the operator’s seat.
1. Reduce engine speed and disengage power take-off

if engaged.

2. Park tractor and implement on level, solid ground.
3. Lower implement to ground or onto non-concrete

support blocks.

4. Put tractor in park or set park brake, turn off engine,

and remove switch key to prevent unauthorized

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic

lines.

6. Wait for all components to come to a complete stop

before leaving the operator’s seat.

Use steps, grab-handles and anti-slip surfaces when

stepping on and off the tractor.

Pre-Assembly Checklist



Check

Ref.

Have a forklift or hoist with properly sized chains and

safety stands on hand capable of lifting and supporting

the equipment.
Have a minimum of two people available during

assembly and set-up.

Make sure all components and loose parts

are with K-Hitch.

Parts

Manual

320-135PK

Double check to make sure all hardware is

installed in the correct location. Refer to the

Parts Manual if unsure.

Parts

Manual

320-135PK

Make sure bolts and nuts are tight.

Operator’s

Manual

Make sure working parts move freely and

cotter pins are spread.

Operator’s

Manual &

Parts

Manual

320-135PK

Make sure all grease fittings are installed

and lubricated.

Operator’s

Manual

Make sure all safety labels are correctly

located and legible. Replace if damaged.

Important

Safety

Information

Содержание K-Hitch AP-KH15

































Результаты поиска

Содержание K-Hitch AP-KH15

Отзывы:

Бренды по названию

Популярные бренды

Kubota K-Hitch AP-KH15, Руководство оператора

Результаты поиска

Содержание K-Hitch AP-KH15

Отзывы:

Бренды по названию

Популярные бренды