Kubota D1503-M-E3 Скачать руководство пользователя страница 43

Страница: 43 / 47

SPECIFICATIONS

GLISH

Flywheel type is SAE clutch No. 7-1/2 or its equivalent.

Flywheel housing type is SAE No. 4 or its equivalent.

Continuous will operate at the stated rating continuously and have a 10% overload capability for one hour in 12 hours.

Standby will operate at the stated full rating for one hour in 12 hours. No overload capacity is specified for this rating.

Specifications are subject to change without notice.

Model

D1703-M-E3BG

V2003-M-E3BG

Type

Vertical, water-cooled, 4-cycle diesel engine

Number of cylinders

Bore and stroke
mm (in.)

87 x 92.4

(3.43 x 3.64)

83 x 92.4

(3.27 x 3.64)

Total displacement
L (cu.in.)

1.647

(100.51)

1.999

(121.94)

Combustion chamber

Spherical Type (E-TVCS)

SAE NET Continuous kW / rpm
H.P. (SAEJ1349) (HP / rpm)

15.1 / 1800 (20.2 / 1800)

18.2 / 1800 (24.4 / 1800)

12.8 / 1500 (17.2 / 1500)

15.5 / 1500 (20.8 / 1500)

SAE NET Standby kW / rpm
H.P. (SAEJ1349) (HP / rpm)

18.1 / 1800 (24.3 / 1800)

21.8 / 1800 (29.2 / 1800)

15.0 / 1500 (20.1 / 1500)

18.1 / 1500 (24.3 / 1500)

Maximum bare speed rpm

1800 / 1500

Order of firing

1-2-3

1-3-4-2

Direction of rotation

Counter-clockwise (viewed from flywheel side)

Injection pump

Bosch Type mini pump

Governor

Electronic Governor

Injection pressure Mpa (kgf/cm , psi)

13.73 (140, 1991)

Injection timing (Before T.D.C.)

0.27 rad (15.25 )

Compression ratio

22.0

22.8

Fuel

Diesel Fuel No.2-D (ASTM D975)

Lubricant (API classification)

above CF

Dimension mm (in.)
(length x width x height)

608.4 x 490 x 642.8

(24.0 x 19.3 x 25.3)

700.6 x 490 x 633.3

(27.6 x 19.3 x 24.9)

Dry weight (BB Spec.) kg (lbs.)

164 (361.6)

195 (430.0)

Starting system

Cell starter (with glow plug)

Starting motor

12 V, 1.4 kW

Charging generator

12 V, 480 W

Recommended battery capacity

12 V, 70 to 80 AH,

equivalent

12 V, 100 to 120 AH,

equivalent

E.book 31 ページ２００９年４月２３日　木曜日　午前１０時３１分

Содержание D1503-M-E3
















































Результаты поиска

Содержание D1503-M-E3

Отзывы:

Kubota D1503-M-E3, Руководство оператора, Страница: 43 / 47

Результаты поиска

Содержание D1503-M-E3

Отзывы: