Kubota AP-SC7072 Скачать руководство пользователя

Страница: 12 / 36

Section 1: Assembly & Set-up

Table of Contents

AP-SC7072 Skid Cutter 326-974MK

2/6/19

Hitch Hook-Up

Refer to Figure 1-1:

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the

attachment. Do not allow anyone to stand between attachment

and power machine while approaching or backing away from

the attachment. Do not operate lift and/or tilt controls while

someone is near the power machine and/or attachment.

Make sure hydraulic hoses and height adjustment
safety chain do not interfere with hitch hook-up.

2. Drive skid steer slowly to the Skid Cutter making sure

the front hitch plate of the skid steer is parallel with
the Skid Cutter hitch.

3. Tilt top of skid steer hitch plate slightly forward.

4. Place top of skid steer hitch plate directly under the

Skid Cutter top angle bar.

5. Slowly lift skid steer hitch until it fully contacts the

Skid Cutter top angle bar.

6. Slowly rotate skid steer hitch plate back.

Engage skid steer lock handles. Make sure the pins
go through the bottom slots of the Skid Cutter’s hitch
and the handles lock down.

NOTE:

If the skid steer is not equipped with

hydraulic lock handles, the skid steer must be shut
down and lock handles must be manually engaged.
Refer to

“Skid Steer Shutdown Procedures”

page 16.

Skid Steer Hook-Up

Figure 1-1

70405

Top Angle Bar

Bottom Slots

Height Adjustment Safety Chain (Chain must run under the upper
cross tube and skid steer hitch plate then attach to Skid Steer’s
lower hitch loop). See Figure 1-2.

Female Coupler

Male Coupler

Blade Bolt Access Hole

Zip tie hydraulic hoses together.

Upper Cross Tube

Hose ring

Refer to Figure 1-2

8. Connect the safety chain to the skid steer. For

additional information on how to adjust the safety
chain, see

“Height Adjustment Safety Chain”

page 9.

Height Adjustment Safety Chain (Kubota SVL Shown)

Figure 1-2

70031

Upper cross tube

Skid steer hitch plate

Safety chain stud

IMPORTANT:

The safety chain must run under the

upper cross tube and the skid steer hitch plate or
damage can occur.

Содержание AP-SC7072





































Результаты поиска

Содержание AP-SC7072

Отзывы:

Похожие инструкции для AP-SC7072

Бренды по названию

Популярные бренды

Kubota AP-SC7072, Руководство оператора

Результаты поиска

Содержание AP-SC7072

Отзывы:

Похожие инструкции для AP-SC7072

Бренды по названию

Популярные бренды