manualshive.com logo in svg

Kubota AP-SBL2566, Руководство оператора

Поделиться
Скачать
Kubota AP-SBL2566 Скачать руководство пользователя страница 35

31

Section 6: Maintenance & Lubrication

10/07/16

AP-SBL2566, AP-SBL2574, & AP-SBL2584 Snow Blowers 370-478MK

Table of Contents

Outer Skid Shoe Replacement

Figure 6-4

Outer Skid Shoe Option

Refer to Figure 6-4:

Inspect outer skid shoes for wear and replace as needed.

1.

Park on a level solid surface, place skid steer/tractor 
in park or neutral with park brake set, lower Snow 
Blower until it is approximately 6" above ground, 
disengage hydraulics, and wait for all components to 
stop rotating before dismounting skid steer/tractor.

2.

Place 1 1/2" to 3" thick support block(s) (#5) under 
the grader blade (#1) near the right-hand and left-
hand skid shoes (#2).

3.

Return to the skid steer/tractor and lower the Snow 
Blower onto the support blocks (#5), shut engine off 
and remove switch key. Wait for all components to 
stop rotating before dismounting skid steer/tractor.

4.

Count & record number of square holes “A” from top 
down to the holes carriage bolts (#3) are located.

5.

Remove hex nuts (#4), carriage bolts (#3), and right-
hand skid shoe (#2). Discard skid shoe and save 
hardware for reattachment of new skid shoe.

6.

Using the recorded number in step 4 above, insert 
1/2"-13 x 1 1/4" GR5 carriage bolts (#3) through 
square holes “A” in skid shoe (#2) and the Snow 
Blower side panel. Secure carriage bolts with hex 
flange lock nuts (#4). 

7.

Tighten lock nuts (#4) to the correct torque.

8.

Repeat steps 4 to 7 above for left-hand skid shoe.

9.

If skid shoes need readjusting, refer to 

“Outer Skid 

Shoe Adjustment” 

on page 22.

35607

Outer Skid Shoe Part Numbers

Part No.

Part Description

370-436H

OUTER RIGHT-HAND SKID SHOE SBL66

370-437H

OUTER LEFT-HAND SKID SHOE SBL66

370-449H

OUTER RIGHT-HAND SKID SHOE SBL74/84

370-450H

OUTER LEFT-HAND SKID SHOE SBL74/84

Outer Skid Shoe Assembly

Figure 6-5

Inner Skid Shoe Option

Refer to Figure 6-5:

Inspect inner skid shoes for wear and replace as needed.

1.

Park on a level solid surface, place skid steer/tractor 
in park, and lower both ends of grader blade onto 
support blocks or jack stands that are, at a minimum, 
8 1/2" high.

2.

Shut skid steer/tractor engine off and remove switch 
key.

3.

On the left-hand side, remove hairpin cotter (#2), 
bent pin (#3), and inner skid shoe (#1).

4.

Reinsert new inner skid shoe (#1).

5.

Insert bent pin (#3) through the same holes in the 
skid shoe mount and new skid shoe that it was 
removed from. 

6.

Secure bent pin with hairpin cotter (#2).

7.

Repeat steps 3 & 4 for the right-hand side.

8.

If skid shoes need readjusting, refer to 

“Inner Skid 

Shoe Adjustment” 

on page 22.

37877

Inner Skid Shoe Part Numbers

Part No.

Part Description

370-439H

INNER SKID SHOE

Содержание AP-SBL2566













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды