Kubota 329-181A Скачать руководство пользователя страница 2

Страница: 2 / 16

Assembly Instructions

PS20 Seed Cup Speed Increaser Kit 329-181A Assembly Instructions Manual No. 329-242MK

5/21/21

Removing Pre-existing Chain Guard

Mounts

WARNING

To avoid serious injury or death:
Wear the appropriate personal protective equipment and

clothing when performing tasks such as using a cutting torch,

grinding, and/or welding.

Refer to Figure 1-1:

1. Remove all flammable materials and liquids from the

work area.

2. Using an acetylene torch, remove both pre-existing

chain guard mounts (R) from the seeder.

3. With chain guard mounts (R) removed, use a grinder,

sander or cold chisel to remove any excess slag

produced by the acetylene torch.

IMPORTANT:

Use caution and avoid removing

excess material from the seeder’s steel frame when

removing chain guard mounts.

NOTE:

If material was accidentally removed from

the seeder’s steel frame, gouges can be filled in with

welding tacks, and then sanded flush.

Disassembling Pre-existing Drive

Assembly

Refer to Figure 1-1:

1. Remove chain guard (A) from seeder by unthreading

all three hand knobs (B).

2. Remove the upper drive sub-assembly (D).

a. Raise seedbox lid (J) to access hardware.
b. Remove hex nuts (H), lock washers (G), and flat

washers (F) from inside the seedbox, then remove

bolts (C).

c. Move the upper drive sub-assembly (D) around to

provide slack in chains (E & Q), then remove both

chains from sprockets (U & W).

d. Place all removed components off to the side or

inside a box to avoid mixing old components with

new components waiting to be installed.

3. Remove the lower drive sub-assembly (L).

a. Remove hex nuts (K) and bolts (P) from

mount (S).

b. Remove the lower drive sub-assembly (L),

tensioner bar (N), and both tensioner

bushings (M) from mount (S).

4. Remove lower sprocket (U) from the rear roller

axle (X) by removing bolt (T) and hex nut (V).

IMPORTANT:

All three hand knobs (B) will be

installed onto the new chain guard for this kit.

Disassembling Pre-existing Drive Assembly

Figure 1-1

76263

Assembly Instructions

Содержание 329-181A

















Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды

Kubota 329-181A, Руководство по сборке

Результаты поиска

Содержание 329-181A

Отзывы:

Похожие инструкции для 329-181A

Бренды по названию

Популярные бренды