electric motorcycles
KUBERG
16
electric motorcycles
KUBERG
17
UNPACKING AND ASSEMBLY
7. Compress each brake lever in turn. The
lever should not compress completely to
the bar Each individual brake should
hold the bike securely when you push
the KUBERG against the brake. If your
brake needs adjustment, follow the
instructions on page 20. For beginning
riders adjust the front brake so it will not
lock the wheel easily. Learning riders
should be aware which lever operates
which brake.
8. For maximum battery life, always fully
charge before operating your KUBERG
for the first time. (See page 23 for
charging instructions).
9. While your batteries are charging,
please Read Your Owner's Manual
completely.
unpacking and assembly
switch plate
WARNING!
Failure to properly assemble and adjust your bike prior to use may
result in an accident resulting in death, serious injury and/or property damage. If
you are uncertain about any aspect of the assembly and adjustment of your
bike, seek help from a qualified mechanic or the KUBERG Customer Service
Department.
WARNING!
There are no user serviceable elements incorporated into the
motor, motor controller, batteries, battery charger, throttle, or wiring harness of
your KUBERG electric bike. DO NOT ATTEMPT TO DISASSEMBLE OR ADJUST ANY
OF THESE COMPONENTS. Doing so may cause extensive damage to these com-
ponents, will void your warranty, and may cause a hazardous condition. If you
cannot resolve a problem using this owner's manual, contact your KUBERG
authorized dealer, or call the KUBERG Customer Service Department for
assistance.
NOTE!
If you purchased your KUBERG at a local retailer your motorcycle may be
fully adjusted and ready to ride. If you purchased your KUBERG in the carton, ple-
ase carefully follow the instructions below and any supplemental instructions to
finish the assembly and adjustment of your KUBERG.
1. Remove your KUBERG from the box.
2. Lower kickstand and place your KUBERG
on a solid & level surface.
3. Remove all the packing materials.
4. Using the supplied Allen wrench, make
sure the steering stem is in the forward
facing position and tighten the top and
side bolts securely and evenly. Secure
the handlebars tightly in the steering
stem. Double check tightness and
alignment. Adjust the brake lever
positions to suit the rider.
5. Check tire pressure of both tires and
confirm they are properly inflated to 30-
40 psi.
6. Unpack charger from its box and charge
the batteries while thoroughly reading
the complete owner's manual. (See the
Charging Instructions on pages 23).
Now your KUBERG is fully assembled, adjusted and checked. Once the batteries
are fully charged, your KUBERG will be ready to ride safely.
SWITCH PLATE
The 'switch plate' is under the seat area and is the location for several important items, as
follows:
Power switch
Power switch is
located on the right hand side
of the handle bars.
Always switch the bike into Off position when stopped or parked.
Potentiometer
The 'speed dial' potentiometer allows the responsible adult to
set the speed anywhere from 0 mph to maximum. The position
of the speed dial is deliberately awkward to get to, and should
only be altered by a responsible adult. A screwdriver can be
used for any changes. It is important that all people are away
from the bike during this operation. When you are changing
the settings make sure the side-stand is down. After making a
change, push the bike against the side-stand to raise the rear
wheel. With the power on, turn the twist-grip throttle fully
open to check the top speed. Bear in mind that the dial is not
completely linear. Do not guess the settings. Always check
before allowing the rider back on the bike.
Charger Port
When it's time to recharge the bike, the battery charger
connector attaches to this port. Before attaching, ensure that
the power is switched to the off position. Please refer to the
battery and charging section (page 23) of this manual for more
information
.
Magnetic kill switch
The magnetic kill switch is a safety switch that is located on
the left hand side of the handlebar and will not allow the bike
to operate when the red plug is not attached to it. Always put
the lanyard on the left wrist of the rider and fasten it properly
before each ride. Make sure that the rider has this lanyard on
his wrist all the time he is on his bike. Make sure the Rider
always wear certified off road helmet and goggles.
Please Note:
All pictures are of pre-production prototypes, so could differ from the final
production motorcycles.
owner´s manual
owner´s manual
