KTR ROTEX ZR Скачать руководство пользователя страница 9

 

ROTEX

®

 

Operating/Assembly instructions 

Type ZR 

KTR-N 
Sheet: 
Edition: 

40215 EN 
9 of 15 

 

Please observe protection 

note ISO 16016. 

Drawn: 

2018-08-28 Pz 

Replacing: 

KTR-N dated 2014-03-11 

Verified: 

2018-09-11 Pz 

Replaced by: 

 

 

 

 

 

We recommend to inspect bores, shaft, keyway and feather key for dimensional accuracy 
before assembly. 

 
Heating the hubs lightly (approx. 80 °C) allows for an easier mounting on the shaft. 
 

 

STOP 

 

Touching the heated hubs causes burns. 
Please wear safety gloves. 

 

 

 

With the assembly please make sure that the distance dimension E (see table 1 and 2) is 
observed to allow for axial clearance of the spider when in operation. 
Disregarding this advice may cause damage to the coupling. 

 
 
 

 

  Mount the hubs on the shaft of driving and driven side (see illustration 5). 

  The internal sides of the hubs must be flush with the front sides of the shafts. 

  Shift the power packs in axial direction until the dimension L

R1

 is achieved (see illustration 1). 

  Fasten the hubs by tightening the setscrews DIN EN ISO 4029 with a cup point (tightening torque see table 3). 

 

 

Illustration 5: Assembly of the hubs 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Assembly 

4.3  Assembly of the coupling (general) 

4.4  Assembly of the hubs 

Содержание ROTEX ZR
















Отзывы: