KTM RC 390 страница 153 Скачать руководство пользователя

Страница: 153 / 200

SERVICE WORK ON THE ENGINE

151

18.1

Checking the engine oil level

Condition

The engine is at operating temperature.

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

L02257-10

Main work

–

Check the engine oil level.

Info

After switching off the engine, wait one minute before checking the level.

The engine oil must be between the



and



markings .

» When the engine oil level is below the



marking:

–

Add the engine oil. (

p. 154)

» When the engine oil level is above the



marking:

–

Correct the engine oil level.

18.2

Changing the engine oil and oil filter, cleaning the oil screens

Warning

Danger of scalding

Engine oil and gear oil get very hot when the motorcycle is ridden.

–

Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды