KTM Freeride 350 AU страница 18 Скачать руководство пользователя

Страница: 18 / 116

CONTROLS

6.17

Side stand

401943-10

The side stand



is on the left side of the vehicle.

401944-10

The side stand is used to park the motorcycle.

Info

When you are riding, side stand



must be folded up and secured with rubber

band



6.18

Steering lock

S00832-10

Steering lock



is fitted on the left side of the steering head.

The steering lock is used to lock the steering. Steering, and therefore riding, is no
longer possible.

6.19

Locking the steering

Note

Danger of damage

The parked vehicle may roll away or fall over.

–

Always place the vehicle on a firm and even surface.

400732-01

–

Park the vehicle.

–

Turn the handlebar as far as possible to the right.

–

Grease steering lock regularly.

Universal oil spray (

p. 107)

–

Insert the key in the steering lock (

p. 16), turn it to the left, press it in, and turn

it to the right. Remove the key.

Steering is no longer possible.

Info

Never leave the key in the steering lock.

Содержание Freeride 350 AU





















































































































Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды

KTM Freeride 350 AU, Руководство пользователя

Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды