KTM Freeride 350 AU страница 110 Скачать руководство пользователя | Manualshive

Страница: 110 / 116

background image

26

STANDARDS

108

JASO T903 MA

Different technical development directions required a new specification for 4-stroke motorcycles

–

the JASO T903 MA Standard. Ear-

lier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle specifi-
cation. Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are in the fore-
ground for motorcycle engines. In most motorcycles, the gearbox and the clutch are lubricated with the same oil as the engine. The
JASO MA Standard meets these special requirements.

SAE

The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to their vis-
cosity. The viscosity describes only one property of oil and says nothing about quality.

«
...
108
109
110
111
112
...
»

Содержание Freeride 350 AU





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Freeride 350 AU

Бренд: Öhlins Страницы: 2

Бренд: Yamaha Страницы: 88

Бренд: R&G Страницы: 13

X-903 Ultra Carbon 29

Бренд: X-lite Страницы: 116

Yamaha X-MAX 300

Бренд: BRUUDT Страницы: 7

Бренд: N-Com Страницы: 2

LIX9U0003740299

Бренд: X-lite Страницы: 116

Бренд: kellermann Страницы: 5

Black Seven 250

Бренд: Mash Страницы: 62

Бренд: Marzocchi Страницы: 116

Бренд: KTM Power Parts Страницы: 22

Бренд: KTM Power Parts Страницы: 12

Бренд: KTM Страницы: 7

Бренд: KTM Страницы: 16

125 EXC EU 2014

Бренд: KTM Страницы: 27

2010 250 EXC-F AUS

Бренд: KTM Страницы: 125

2009 250 EXC-F SIX DAYS

Бренд: KTM Страницы: 125

Бренд: KTM Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды