KTM 990 Adventure AUS Скачать руководство пользователя

Страница: 85 / 218

SERVICE WORK ON THE CHASSIS

10.11

Mounting the seat

100505-10

–

Hook projection



of the seat into the storage compartment, lower the seat at the rear

and push it forward at the same time. The two projections



must be inserted into the

frame.

–

Push locking pin



into the lock housing and push the back of the seat down until the

locking pin locks in place with an audible click.

–

Finally, check that the seat is correctly mounted.

10.12

Removing the storage compartment and hanging it to one side

–

Remove the seat. (

p. 82)

100616-10

–

Open the storage compartment. (

p. 38)

–

Remove screws



–

Carefully remove the storage compartment and swing it to the right. Place a cloth
between the right fuel tank and the storage compartment to prevent damage.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды

KTM 990 Adventure AUS, Руководство пользователя

Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды