KTM 85 SX Скачать руководство пользователя

Страница: 7 / 42

ENGLISH

SERIAL NUMBER LOCATIONS

Chassis number

The chassis number is stamped on the right side of the steering head tube.

Enter this number in the field on page no 1.

Engine number

The engine number is stamped into the engine housing underneath the

carburetor. Enter this number in the field on page no 1.

Clutch lever

The clutch lever

[1]

is located on the left side of the handlebar. The adjust-

ing screw

[A]

is used to change the original position of the clutch lever (see

maintenance work on chassis and engine).

The clutch is hydraulically actuated and adjusts itself automatically.

Hand brake lever

The hand brake lever

[2]

is mounted on the handle bars on the right and actu-

ates the front wheel brake.The adjusting screw

[B]

is used to change the orig-

inal position of the hand brake lever (see maintenance work on chassis and

engine).

OPERATION INSTRUMENTS

Содержание 85 SX











































Результаты поиска

Содержание 85 SX

Отзывы:

Похожие инструкции для 85 SX

Бренды по названию

Популярные бренды

KTM 85 SX, Руководство пользователя

Результаты поиска

Содержание 85 SX

Отзывы:

Похожие инструкции для 85 SX

Бренды по названию

Популярные бренды