KTM 50 SX 2017 Скачать руководство пользователя

Страница: 82 / 104

SERVICE WORK ON THE ENGINE

16.1

Checking oil level (50 SX Mini)

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

H00056-10

Main work

–

Check the oil level in the oil tank.

For a full fuel tank, the oil tank must be filled up to

MIN

mark



at a minimum.

» If the oil level does not meet specifications:

–

Fill up with oil. (

p. 21)

16.2

Bleeding the oil pump (50 SX Mini)

Condition

The fuel tank has been removed.

H00080-10

–

Pull off oil line



300652-10

–

Fill the oil line with a syringe.

Engine oil, 2-stroke (

p. 93)

H00080-10

–

Connect oil line



300651-10

–

Remove screws



–

Take off the oil pump.

–

Pull off oil line



from the carburetor.

Содержание 50 SX 2017









































































































Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды

KTM 50 SX 2017, Руководство пользователя

Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды