KTM 50 SX 2017 Скачать руководство пользователя | Manualshive

Страница: 78 / 104

background image

15

TUNING THE ENGINE

76

Guideline

Choke function deactivated

–

Choke knob is in lower position. The O-ring is not

visible. (

Idle speed

1,400… 1,500 rpm

–

Turn the idle adjusting screw



slowly clockwise until the idle speed begins to

fall.

–

Note the position and turn the idle adjusting screw slowly counterclockwise until
the idle speed falls.

–

Adjust to the point between these two positions with the highest idle speed.

Info

If the speed rise is too high, reduce the idle speed to a normal level and
repeat the preceding steps.
If the procedure described here does not lead to satisfactory results, the
cause may be a wrongly dimensioned idling jet.
If you can turn the idle adjusting screw to the end without any change of
engine speed, you have to install a smaller idling jet.
After changing the idling jet, start from the beginning with the adjusting
steps.
Following extreme air temperature or altitude changes, adjust the idle speed
again.

15.7

Carburetor - adjusting idle speed (50 SX Mini)

H00078-10

–

Screw in idle air adjusting screw



all the way and turn it to the specified basic

position.
Guideline

Idle air adjusting screw

Open

1 turn

–

Run the engine until warm.
Guideline

Warming-up phase

≥

5 min

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result

in unconsciousness and death.

–

Always make sure there is sufficient ventilation when running the
engine.

–

Use an effective exhaust extraction system when starting or running the
engine in an enclosed space.

–

Adjust the idle speed using the idle speed adjusting screw



.

Guideline

Choke function deactivated

–

The choke lever is pushed down all the way to the

stop. (

Idle speed

1,400… 1,500 rpm

–

Turn idle air adjusting screw



slowly in a clockwise direction until the idle speed

begins to fall.

–

Note the position and turn the idle air adjusting screw slowly counterclockwise until
the idle speed falls again.

–

Adjust to the point between these two positions with the highest idle speed.

«
...
76
77
78
79
80
...
»

Содержание 50 SX 2017









































































































Отзывы:

Нет отзывов

Похожие инструкции для 50 SX 2017

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

PAMPERA 400 - 2006

Бренд: GAS GAS Страницы: 70

Бренд: Suzuki Страницы: 151

Бренд: KTM Power Parts Страницы: 12

Бренд: RDMOTO Страницы: 3

Бренд: JAWA Страницы: 22

Бренд: R&G Страницы: 2

Бренд: R&G Страницы: 9

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 6

Бренд: DAINESE Страницы: 59

VarioProtect XXL-W TC AIR TH3

Бренд: schweisskraft Страницы: 28

Бренд: MARTINDALE Страницы: 39

Бренд: Benelli Страницы: 454

Бренд: Kinroad Страницы: 27

PEGASO 650 I.E. STRADA

Бренд: APRILIA Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды