KTM 450 SMR 2021 Скачать руководство пользователя

Страница: 81 / 139

BRAKE SYSTEM 12

V01355-10

–

Detach spring

–

Loosen nut

and, with push rod

, turn it back until you

have maximum free travel.

–

To adjust the basic position of the foot brake lever to individ-
ual requirements, loosen nut

and turn screw

accord-

ingly.

Info

The range of adjustment is limited.

–

Turn push rod

accordingly until you have free travel

. If

necessary, adjust the basic position of the foot brake lever.
Guideline

Free travel at foot brake lever 3 … 5 mm (0.12 … 0.2 in)

–

Hold push rod

and tighten nut

Guideline

Remaining nuts,
chassis

10 Nm (7.4 lbf ft)

–

Hold screw

and tighten nut

Guideline

Nut, foot brake lever
stop

20 Nm (14.8 lbf ft)

–

Attach spring

12.9

Checking the rear brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is
leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized
KTM workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service
schedule. (Your authorized KTM workshop will be glad to help.)

Preparatory work

–

Check the brake linings of the rear brake. (

p. 81)

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды