KTM 450 SMR 2021 Скачать руководство пользователя

Страница: 80 / 139

12 BRAKE SYSTEM

V01453-11

–

Fill brake fluid up to the

MAX

marking.

Brake fluid DOT 4 / DOT 5.1 (

p. 126)

–

Position cover

with membrane

. Mount and tighten

screws

Info

Clean up overflowed or spilled brake fluid immediately
with water.

12.7

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear
brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

402026-10

–

Disconnect spring

–

Move the foot brake lever back and forth between the end stop
and the contact to the foot brake cylinder piston and check
free travel

Guideline

Free travel at foot brake lever 3 … 5 mm (0.12 … 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.
(

p. 78)

–

Reconnect spring

12.8

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear
brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды