KTM 450 Rally Factory Replica 2014 Скачать руководство пользователя

Страница: 56 / 126

SERVICE WORK ON THE CHASSIS

12.27

Checking the chain, rear sprocket, engine sprocket, and chain guide

Preparatory work

–

Raise the motorcycle with the lift stand. (

p. 41)

400227-01

Main work

–

Shift gear to neutral.

–

Check the rear sprocket and engine sprocket for wear.
» If the rear sprocket and engine sprocket are worn:

–

Change the drivetrain kit.

Info

The engine sprocket, rear sprocket, and chain should always be
replaced together.

1 2 3

16 17 18

400987-10

–

Pull on the upper part of the chain with the specified weight

Guideline

Weight, chain wear measurement

10… 15 kg (22… 33 lb.)

–

Measure the distance

of 18 chain links in the lower chain section.

Info

Chain wear is not always even, so you should repeat this measurement at
different chain positions.

Maximum distance

at the longest

chain section

272 mm (10.71 in)

» If the distance

is greater than the specified measurement:

–

Change the drivetrain kit.

Info

When the chain is replaced, the rear sprocket, and engine sprocket
should also be changed.
New chains wear out faster on old, worn sprockets.

601358-10

–

Check the chain sliding guard for wear.
» If the bottom edge of the chain bolt is in line with or below the chain sliding

guard:

–

Change the chain sliding guard.

–

Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:

–

Tighten the chain sliding guard.
Guideline

Screw, chain sliding
guard

6 Nm
(4.4 lbf ft)

Loctite

243™

Содержание 450 Rally Factory Replica 2014































































































































Результаты поиска

Содержание 450 Rally Factory Replica 2014

Отзывы:

Похожие инструкции для 450 Rally Factory Replica 2014

Бренды по названию

Популярные бренды

KTM 450 Rally Factory Replica 2014, Руководство пользователя

Результаты поиска

Содержание 450 Rally Factory Replica 2014

Отзывы:

Похожие инструкции для 450 Rally Factory Replica 2014

Бренды по названию

Популярные бренды