KTM 2009 690 Rally Factory Replica страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 104

background image

MAINTENANCE WORK ON CHASSIS AND ENGINE

43

8.36

Checking free play of hand brake lever

Warning

Danger of accidents

Brake system failure.

–

If there is no free travel on the hand brake lever, pressure builds up on the front brake in the brake system. The front brake
can fail due to overheating. Adjust free travel on hand brake lever according to specifications.

400290-11

–

Pull the hand brake lever and check the free travel



.

Free play of hand brake lever

≥

3 mm (

≥

0.12 in)

» If the free travel does not meet specifications:

–

Adjust the free travel of the handbrake lever. (

8.37

Adjusting free travel of handbrake lever

400290-12

–

Adjust the free travel of the handbrake lever with the adjustment screw



.

Info

Turn the adjustment screw clockwise to reduce free travel. The pressure
point moves away from the handlebar.
Turn the adjustment screw counterclockwise to increase free travel. The
pressure point moves towards the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not apply any force.
Do not make any adjustments while riding!

–

Check the free play of the hand brake lever. (

8.38

Checking the front brake fluid level

Warning

Danger of accidents

Brake system failure.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings.

Have the brake system checked in an authorized KTM workshop, and do not ride any further.

Warning

Danger of accidents

Reduced braking due to old brake fluid.

–

Have the front and rear brake fluid replaced according to the service plan in an authorized KTM workshop.

600010-11

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Check the brake fluid level in the viewer



.

» If the brake fluid level is below the

MIN

mark:

–

Add front brake fluid.

«
...
43
44
45
46
47
...
»

Содержание 2009 690 Rally Factory Replica









































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 690 Rally Factory Replica

Бренд: R&G Страницы: 13

Бренд: R&G Страницы: 6

Бренд: KYMCO Страницы: 55

Stelvio 1200 MY11 2011

Бренд: MOTO GUZZI Страницы: 385

Бренд: R&G Страницы: 6

MULTISTRADA 1200S

Бренд: Ducati Страницы: 311

Бренд: X-lite Страницы: 84

MASTERFOX 125cc 2015

Бренд: d'Magna Страницы: 29

Бренд: N-Com Страницы: 2

Бренд: ICON Vehicle Dynamics Страницы: 4

Бренд: VESPA Страницы: 135

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Бренд: Aosom Страницы: 13

XSM POWER UP 2007

Бренд: Malaguti Страницы: 53

Бренд: RIEJU Страницы: 147

Бренд: MT Helmets Страницы: 116

Бренд: Benelli Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды