background image

-23- 

3.5 Configuration for SNMP Management 

The switch supports SNMP v1, SNMP v2c, and SNMP v3 management. Make sure the related settings are 

well-configured for the switch before you start the SNMP management from an SNMP manager. 

 

Using Telnet Interface 

The following are available commands in telnet SNMP command group to configure SNMP-related settings: 

 >SNMP 

Configuration 

 

>SNMP Mode [enable|disable] 

 

>SNMP Version [1|2c|3] 

 

>SNMP Read Community [<community>] 

 

>SNMP Write Community [<community>] 

 

>SNMP Trap Mode [enable|disable] 

 

>SNMP Trap Version [1|2c|3] 

 

>SNMP Trap Community [<community>] 

 

>SNMP Trap Destination [<ip_addr_string>] 

 

>SNMP Trap Authentication Failure [enable|disable] 

 

>SNMP Trap Link-up [enable|disable] 

 

>SNMP Trap Inform Mode [enable|disable] 

 

>SNMP Trap Inform Timeout [<timeout>] 

 

>SNMP Trap Inform Retry Times [<retries>] 

 

>SNMP Trap Probe Security Engine ID [enable|disable] 

 

>SNMP Trap Security Engine ID [<engineid>] 

 

>SNMP Trap Security Name [<security_name>] 

 

>SNMP Engine ID [<engineid>] 

 

>SNMP Community Add <community> [<ip_addr>] [<ip_mask>] 

 

>SNMP Community Delete <index> 

 

>SNMP Community Lookup [<index>] 

 

>SNMP User Add <engineid> <user_name> [MD5|SHA] [<auth_password>] [DES] [<priv_password>] 

 

>SNMP User Delete <index> 

 

>SNMP User Changekey <engineid> <user_name> <auth_password> [<priv_password>] 

 

>SNMP User Lookup [<index>] 

 

>SNMP Group Add <security_model> <security_name> <group_name> 

Содержание KGS-2421


























Отзывы: