KSB PumpDrive Скачать руководство пользователя страница 41

Страница: 41 / 162

6.2.1

LED traffic light function

The LED traffic light function provides information about the current PumpDrive
operating status.
Table 31: LED description

LED

Description

Red

One or more than one alert is active

Amber

One or more than one warning is active

Green

Steady light: Trouble-free operation
Flashing light: Trouble-free operation at active master
control panel in a multiple pump configuration

6.2.2

Graphical display

The graphical display breaks down into 6 areas.

3-1-1-1

OFF

B-HMI-C

STOP

Grund-Einstell
Sprache
LCD-Beleuchtung

Leuchtdauer

1
2
3

Fig. 23: Graphical display (example)

Table 32: Description of display

Item

Description

Explanation

Parameter No.

Displays the selected parameter No.

Main menu selection

Displays the main menu selected

▪

Operation

▪

Diagnosis

▪

Settings

▪

Information

Parameter selection list

List of selectable parameters/parameter information

Operating mode

Displays the current operating mode

▪

Man

▪

OFF

▪

Auto

Model

Displays the model, e.g. A-HMI-C
PumpDrive model

= Advanced

= Basic

HMI

= with control panel

Access level

= Customer

= Service

= No login

Pump selected

▪

Pump 1

▪

Pump 2

▪

...

▪

Pump 6

Operating status

Display of current operating status

6 Operation

PumpDrive

41 of 162

Содержание PumpDrive



































































































































































Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды

KSB PumpDrive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды