KSB PumpDrive Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 162

background image

6.1.2

LED display (for standard control panel only)

MAX

MIN

DPM
MODE

1

2

3

Fig. 21: LED display

1

LED bar graph display

2

DPM LED

3

Mode LED

The LED bar graph display shows the setpoint, actual value or speed.
The LED bar graph display can display three different colours. The colours represent
specific operating parameters.
Table 24: Meaning of LED bar graph display colours

LED colour

Associated operating parameter

Red

Motor frequency

Amber

Sensor actual value

Green

Setpoint

The current values of these three operating parameters are shown by means of the
five individual LEDs. Every LED is assigned a percentage range.
Table 25: LED bar graph display states

LED

Percentage range

MIN LED

0-19%

2nd LED

20-39%

3rd LED

40-59%

4th LED

60-79%

MAX LED

80-100%

The full-scale value of 100 % of the MAX LED can have the following meaning:

▪

The maximum motor frequency (e.g. 50 Hz

≙

100 %) has been reached.

▪

The full-scale value of the sensor (e.g. 6 bar

≙

100 %) has been reached.

▪

The setpoint specified in open-loop control mode (e.g. 50 Hz

≙

100 % setpoint)

has been reached.

▪

The setpoint specified in closed-loop control mode (full-scale value of the sensor

≙

100 % setpoint setting) has been reached.

The DPM LED indicates whether a redundant dual-pump control function was
activated (only if DPM module is installed).
The DPM LED can display three different colours. The colour indicates which function
is assigned to PumpDrive:
Table 26: DPM LED states

LED

Function of PumpDrive

Green

Master PumpDrive

Flashing green

Aux. master PumpDrive

No display

PumpDrive in single-pump configuration

The mode LED shows the current operating mode of PumpDrive:
Table 27: Mode LED states

LED

Function of PumpDrive

Red

OFF mode, switched off

Amber

Automatic mode

Green

Manual mode

LED bar graph display

DPM LED

Mode LED

6 Operation

38 of 162

PumpDrive

«
...
36
37
38
39
40
...
»

Содержание PumpDrive



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PumpDrive

Бренд: Fagor Страницы: 56

MINAS A5 Series

Бренд: Panasonic Страницы: 19

Бренд: YASKAWA Страницы: 566

Бренд: YASKAWA Страницы: 526

Бренд: YASKAWA Страницы: 28

Бренд: YASKAWA Страницы: 21

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 11

Kinetix 5100 2198-E1004-ERS

Бренд: Allen-Bradley Страницы: 500

MASTERFLEX L/S 7523-40

Бренд: Cole Parmer Страницы: 23

Бренд: Ricoh Страницы: 37

Бренд: Geckodrive Страницы: 12

Бренд: AMX Страницы: 2

DVDirect VRD-MC3

Бренд: Sony Страницы: 88

Бренд: Shanghai Siheng Motor Страницы: 39

Бренд: Horton Страницы: 44

CMMT-AS-C7/12-11A-P3-S1

Бренд: Festo Страницы: 16

CMMT-AS-C2-11A-P3 S1 Series

Бренд: Festo Страницы: 16

Бренд: Festo Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды