KSB Magnochem-Bloc Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 96

background image

3 Transport/Temporary Storage/Disposal

14 of 96

Magnochem-Bloc

Fig. 3:

Transporting the pump

3.3 Storage/preservation

If commissioning is to take place some time after delivery, we recommend that the
following measures be taken for pump (set) storage.

CAUTION

Damage during storage due to humidity, dirt or vermin

Corrosion/contamination of the pump (set)!

▷

For outdoor storage cover the pump (set) or the packaged pump (set) and
accessories with waterproof material.

CAUTION

Wet, contaminated or damaged openings and connections

Leakage or damage to the pump!

▷

Clean and cover pump openings and connections as required prior to putting
the pump into storage.

Store the pump (set) in a dry, protected room where the atmospheric humidity is as
constant as possible.

Rotate the shaft by hand once a month, e.g. via the motor fan.

If properly stored indoors, the pump set is protected for a maximum of 12 months.
New pumps/pump sets are supplied by our factory duly prepared for storage.

For storing a pump (set) which has already been operated, the shutdown measures
must be adhered to. (

Section 6.3.1, Page 42)

3.4 Return to supplier

1. Drain the pump as per operating instructions. (

Section 7.3, Page 50)

2. Flush and clean the pump, particularly if it has been used for handling noxious,

explosive, hot or other hazardous fluids.

3. If the pump has handled fluids whose residues could lead to corrosion damage

in the presence of atmospheric humidity or could ignite upon contact with
oxygen also neutralise the pump and blow through with anhydrous inert gas to
ensure drying.

4. Always complete and enclose a certificate of decontamination when returning

the pump.
Indicate any safety measures and decontamination measures taken.
(

Section 11, Page 90)

NOTE

If required, a blank certificate of decontamination can be downloaded from the
following web site:

www.ksb.com/certificate_of_decontamination

«
...
12
13
14
15
16
...
»

Содержание Magnochem-Bloc

































































































Отзывы:

Нет отзывов

Похожие инструкции для Magnochem-Bloc

Бренд: Kanomax Страницы: 26

Бренд: Macnaught Страницы: 20

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренд: IFR Страницы: 46

Бренд: Nellcor Страницы: 104

Бренд: PAT Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды