KSB AmaSlide KB16-AH280 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

background image

5 Installation at Site

15 of 32

AmaSlide

2553.870/01-EN

5 Installation at Site

5.1 Safety regulations

DANGER

Improper installation in potentially explosive atmospheres

Damage to the pump set!

▷

Comply with the applicable local explosion protection regulations.

▷

Observe the information given in the data sheet and on the pump/motor name
plates.

5.2 Checks to be carried out prior to installation

WARNING

Improper installation of the pump set

Personal injury and damage to property!

▷

Observe the following instructions for positioning and installing the pump set
to prevent substantial hazards and injuries.

Place of installation

WARNING

Installation on mounting surface which is unsecured and cannot support the load

Personal injury and damage to property!

▷

Use a concrete of compressive strength class C12/15 which meets the
requirements of exposure class XC1 to EN 206-1.

▷

The mounting surface must be set, flat, and level.

▷

Observe the weights indicated.

1. Check the structural requirements.

All structural work required must have been prepared in accordance with the
dimensions to ensure the maintenance aid can be moved into servicing position.
(

Section 8.2, Page 27)

Power cable

CAUTION

Power cable not properly routed

Damage to the power cable!

▷

The power cable must be routed in such a way that it cannot become damaged
when the maintenance aid is operated.
Observe the dimensions indicated. (

Section 8.2, Page 27)

1. Check the position of the power cable.

The power cable must be positioned so as not to obstruct the back pull-out unit
when it is moved from the operating position to the servicing position.

«
...
13
14
15
16
17
...
»

Содержание AmaSlide KB16-AH280

































Отзывы:

Нет отзывов

Похожие инструкции для AmaSlide KB16-AH280

Бренд: Quantum Страницы: 20

geoTHERM SERIES

Бренд: Vaillant Страницы: 112

geoTHERM SERIES

Бренд: Vaillant Страницы: 132

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

Бренд: Gianneschi Страницы: 28

Бренд: Hi-Force Страницы: 16

Бренд: Ocean Aire Страницы: 36

Бренд: Ultranatura Страницы: 24

Бренд: Speck pumpen Страницы: 8

Бренд: Samoa Страницы: 32

Бренд: Biral Страницы: 104

Бренд: Goodman Страницы: 56

Бренд: Pfeiffer Vacuum Страницы: 64

Wright Flow Technologies RTP Series

Бренд: Idex Страницы: 58

AlwaysFresh HFC-1000

Бренд: Waterline Technology Страницы: 6

Бренд: REMEHA Страницы: 48

Бренд: Lowara Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды