Krone KW 5.50 / 4 x 7 T Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 42

background image

III - 7

Switch off the engine and remove the
ignition key. Protect the tractor from
rolling. Only then pull off the PTO
shaft.

The holding chains of the protective
tubes are not designed or suitable for
holding up the PTO shaft.

•

Loosen the holding chain, pull off the PTO shaft and
lay it on the PTO shaft support bracket (1).

•

Uncouple hydraulic hose (4) from the tractor and
install the dust cap.

•

Remove plastic rope (5) from the tractor.

•

Uncouple the rotary tedder from the tractor.

When the hydraulic hose is being
coupled to or uncoupled from the
tractor, the hydraulic system of both
the tractor and the mowing attachment
must be free from pressure. The
corresponding control valves must be
moved to float position.

KW000012

1

3

2

4

5

«
...
23
24
25
26
27
...
»

Содержание KW 5.50 / 4 x 7 T











































Отзывы:

Нет отзывов

Похожие инструкции для KW 5.50 / 4 x 7 T

Бренд: Confer Plastics Страницы: 3

Бренд: Confer Plastics Страницы: 6

Бренд: Confer Plastics Страницы: 6

FORTRESS OSHA Stair System

Бренд: EZ-ACCESS Страницы: 6

Бренд: STACKER Страницы: 24

LYTEPOD BS 8620

Бренд: Lyte Industries Страницы: 2

Бренд: Lyte Industries Страницы: 2

Бренд: Lyte Страницы: 3

Бренд: Clas Ohlson Страницы: 2

Бренд: Clas Ohlson Страницы: 28

Бренд: habitat et jardin Страницы: 31

Бренд: Rivers Edge Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды