Krone EasyCut F 320 Скачать руководство пользователя страница 12

Страница: 12 / 86

Safety

2.1

Intended use

Original Operating Instructions 150000802_00_en

Safety

2.1

Intended use

The machine is used to mow crop.
Blades and leaves growing on the ground represent the crop provided for the intended use of

this machine.
The machine is designed exclusively for use in agriculture and may only be used when
•

all safety devices are available according to the operating instructions and are located in the

protective position.

•

all safety instructions mentioned in the operating instructions are observed and complied

with.

The machine must only be used by people who satisfy the personnel qualification requirements

designated by the machine manufacturer,

refer to page 13

The operating instructions are part of the machine. Therefore they have to be kept ready to

hand for the user of the machine.
If the machine is used for applications which are not described in these operating instructions,

this may result in serious injuries or death and damage to the machine and other property.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt

the proper operation. For this reason, unauthorised modifications shall exclude any liability of

the manufacturer for consequential damage.
The intended use shall also include the adherence to the operating, maintenance and repair

conditions set by the manufacturer.

2.2

Service life of the machine

•

The service life of this machine depends on appropriate operation and maintenance as well

as on operating conditions.

•

Permanent operational readiness as well as long service life of the machine can be

achieved by following the instructions and notes of these operating instructions.

•

After each season of use, the machine must be checked completely for wear and other

damage.

•

Replace damaged and worn parts before placing the machine into service again.

•

After the machine has been used for five years, carry out full technical inspection of the

machine. According to the results of this inspection, a decision concerning the possibility of

reuse of the machine should be taken.

•

Theoretically, the service life of this machine is unlimited as all worn or damaged parts can

be replaced.

2.3

Basic safety instructions

Non-observance of safety instructions and warning signs

Failure to comply with the safety instructions and warning signs can lead to risk for people,

environment and property.

2.3.1

Importance of operating instructions

The operating instructions are an important document and a part of the machine. They are

aimed at the user and contain safety-relevant information.

Содержание EasyCut F 320























































































Результаты поиска

Содержание EasyCut F 320

Отзывы:

Похожие инструкции для EasyCut F 320

Бренды по названию

Популярные бренды

Krone EasyCut F 320, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание EasyCut F 320

Отзывы:

Похожие инструкции для EasyCut F 320

Бренды по названию

Популярные бренды