Krom Schroder ZMI Скачать руководство пользователя страница 4

GB-4

D

GB

F

NL

I

E

  

  Check that the burner block hole is not blocked, 

e.g. using a wooden stick.

ZMIC

7

6

5

4

Position the 

burner before 

tightening the 

burner bracket.

  8  

  Follow the reverse procedure when dismantling.

ZMIC..K

7

6

5

4

Position the 

burner before 

tightening the 

bellows unit nut.

Secure the bel-
lows unit here 
while tightening 
the bellows unit 
nut.

Wiring

 DANGER

Electric shocks can be fatal! Before working on 
possible live components, ensure the unit is discon-
nected from the power supply.

 

For the ionization and ignition cables, use un-
screened high-voltage cable:

 

FZLSi 1/7 -50 to +180°C (-58 to +356°F),

 

Order No. 04250410,

 or  
 

FZLK 1/7 -5 to +80°C (23 to 176°F),

 

Order No. 04250409.

 

Wire the burner as shown in the connection 
diagrams of the automatic burner control unit/

ignition transformer.

 

Flame control and ignition by a single electrode 
(single-electrode operation).

 

  Route the PE wire directly to the automatic burner 

control unit.

Leak test

 DANGER

Risk of explosion and poisoning! 

To ensure that 

there is no danger resulting from a leak, check the 
gas connections on the burner for leaks immediately 
after the burner has been put into operation.

1

2

Содержание ZMI










Отзывы: