KROHNE SMARTMAC 200 W Скачать руководство пользователя страница 3

 SAFETY INSTRUCTIONS 

1

3

SMARTMAC 200 W

www.krohne.com

09/2017 - 4005599202 - AD Ex SMARTMAC 200 en R02

1.1  General notes

These supplementary instructions apply to versions of the loop powered
display and operating unit for use in hazardous areas that fall in intrinsically safe protection type 
"i", equipment category II 2 G or EPL Gb. It complements the standard documentation for 
versions for use in non-hazardous areas.

The information given in these instructions contains only the data relevant to explosion 
protection. The technical details given in the standard documentation for the non-explosion 
protected versions remain unchanged unless they will be excluded or replaced by this 
instruction.

1.2  EU conformity

The manufacturer declares with the EU declaration of conformity on his own responsibility 
conformity with the protection goals of directive 2014/34/EU for use in hazardous areas with gas.

Conformity with harmonised standards was checked by a notified body in accordance with 
EN 60079-0:2012 and EN 60079-11:2012.
The EU declaration of conformity for the equipment category II 2G is based on the following EU 
type examination certificate:

The "X" after the certificate number refers to special conditions for safe use of the device, which 
have been listed in these instructions.
If necessary, the EU type examination certificate can be downloaded from the manufacturer's 
website.

1.3  Approval according to the IECEx scheme

Conformity for use in hazardous areas with gas was tested in accordance with the IECEx 
Certification Scheme for Explosive Atmospheres acc. to IEC 60079-0: 2011 and IEC 60079-11: 
2011.
The number of the IEC certificate is:

The "X" after the certificate number refers to special conditions for safe use of the device, which 
have been listed in these instructions.
If needed, the IEC certificate can be downloaded from the manufacturer's website.

KIWA 16 ATEX 0027 X

KIWA 16 ATEX 0027 X

KIWA 16 ATEX 0027 X

KIWA 16 ATEX 0027 X

IECEx KIWA 16.0011 X

IECEx KIWA 16.0011 X

IECEx KIWA 16.0011 X

IECEx KIWA 16.0011 X

Содержание SMARTMAC 200 W

















Отзывы: