KROHNE OPTISWITCH 4000 C Скачать руководство пользователя страница 3

Страница: 3 / 32

1 About this document

OPTISWITCH 4000 C • Transistor (PNP)

42372-EN-191122

1 About this document

1.1 Function

This instruction provides all the information you need for mounting,

connection and setup as well as important instructions for mainte-

nance, fault rectification, the exchange of parts and the safety of the

user. Please read this information before putting the instrument into

operation and keep this manual accessible in the immediate vicinity

of the device.

1.2 Target group

This operating instructions manual is directed to trained personnel.

The contents of this manual must be made available to the qualified

personnel and implemented.

1.3 Symbols used

Information, note, tip: This symbol indicates helpful additional infor-

mation and tips for successful work.
Note: This symbol indicates notes to prevent failures, malfunctions,

damage to devices or plants.
Caution: Non-observance of the information marked with this symbol

may result in personal injury.
Warning: Non-observance of the information marked with this symbol

may result in serious or fatal personal injury.
Danger: Non-observance of the information marked with this symbol

results in serious or fatal personal injury.
Ex applications

This symbol indicates special instructions for Ex applications.

•

List

The dot set in front indicates a list with no implied sequence.

1 Sequence of actions

Numbers set in front indicate successive steps in a procedure.
Battery disposal

This symbol indicates special information about the disposal of bat-

teries and accumulators.

Содержание OPTISWITCH 4000 C

































Результаты поиска

Содержание OPTISWITCH 4000 C

Отзывы:

Похожие инструкции для OPTISWITCH 4000 C

Бренды по названию

Популярные бренды

KROHNE OPTISWITCH 4000 C, Руководство пользователя

Результаты поиска

Содержание OPTISWITCH 4000 C

Отзывы:

Похожие инструкции для OPTISWITCH 4000 C

Бренды по названию

Популярные бренды