KROHNE Altosonic III, Инструкция по установке и эксплуатации

Страница: 16 / 43

ALTOSONIC III 16
Key Measuring mode Menu mode Data level
→ Go to the parameter setting mode, function 1.00.00
OPERATION. If access CODE 1 is activated, CODE 1 must be
entered first. Using function 3.07.02 access CODE 1 can be
activated or deactivated. Go to the next, lower menu level. Go to the next character or change line
(only when 2 lines are displayed)
↵ Go to the error/Totalizer reset mode (via "CODE 2") Return to the previous (higher)
menu level or leave the menu
mode. Accept entered value
↑ Cycle through measured values, see Function 3.03.07 CYCL
DISP Cycle through menu options
within actual menu level. Cycle active digit up to new values
Function Text Description and settings
0.00.00 ERROR/TOT Main menu 0.00.00
0.00.01 VIEW ERR View error messages list
0.00.02 RST ERR Reset error messages
0.00.03 UP2 SW NO Software version micro processor 2
0.00.04 DSP SW NO Software version digital signal processor
0.00.05 DISPLAY Display test, all display items on
0.00.06 EXIT Leave menu 0.00
1.00.00 OPERATION Main menu 1.00.00 Operation
1.01.00 FLOW Submenu 1.01.00 Flow
1.01.01 FULL SCALE Full-scale value for 100% volume flow rate, see Function 3.01.01
1.01.02 ZERO VALUE Zero value, see Function 3.01.02
1.01.03 ZERO CAL Zero calibration, see Function 3.01.03
1.01.04 MASTER TC Master time constant, see Function 3.01.04
1.01.05 LF CUTOFF Low-flow cut-off, see Function 3.01.05
1.01.06 CUTOFF ON Cut-off active, see Function 3.01.06
1.01.07 CUTOFF OFF Cut-off de-active, see Function 3.01.07
1.02.00 DISPLAY Submenu 1.02.00 Display
1.02.01 DISP FLOW Display of flow, see Function 3.03.01
1.03.00 PULSE OUTP Submenu 1.03.00 Pulse output
1.03.01 PULSE RATE Pulse frequency value for 100% scale, see Function 3.05.08
1.03.02 PULSE/UNIT Pulse value per volume flow unit, see Function 3.05.09
2.00.00 TEST Main menu 2.00.00 Test functions
2.01.00 DISPLAY Submenu 2.01.00 Display
2.01.01 DISPLAY
Test display, lights all pixels. End with
↵
key
2.02.00 OUTPUTS Submenu 2.02.00 Outputs
2.02.01 CURRENT Test current output
0 mA
4 mA
12 mA 20 mA
22 mA
Use up arrow to advance. Displayed value directly present at current output. Actual value present at
output after pressing
↵
key.
2.02.02 PULSE Test pulse/frequency output
1 Hz
10 Hz
100 Hz 1000 Hz
2000 Hz
Use the up arrow to advance. Displayed value directly present at Pulse output. Actual value present at
output after pressing
↵
key
2.03.00 INPUTS Submenu 2.03.00 Inputs
2.03.03 DIG INPUT Test digital input
Measure level at digital input. End with
↵
key.
2.04.00 DEV INFO Submenu 2.04.00 Device information
2.04.01 MANUFACT Display manufacturer
2.04.02 MODEL NO Display model number
2.04.03 SERIAL NO Display serial number
2.04.04 UP2 HW NO Display µP2 hardware number
2.04.05 UP2 SW NO Display µP2 software number
2.04.06 FRNT HW NO Display front end hardware number
2.04.07 DSP HW NO Display D.S.P. hardware number
2.04.08 DSP SW NO Display D.S.P. software number
2.04.09 TIME COUNT Display time counter
3.00.00 INSTALL Main menu 3.00.00 Installation
3.01.00 FLOW Submenu 3.01.00 Volume flow parameters