KRM KRM-100 Скачать руководство пользователя страница 9

Страница: 9 / 33

KRM

[KRM-100] MIDI-CV-Arpeggiator

3 Changing the Default Configuration

The default configuration of the [KRM-100] assumes the most common setup:

•

1 V/octave response.

•

5 volt V-trig gate.

•

Lowest key on the MIDI controller corresponds to low C (MIDI note 36)

•

Listen on MIDI channel 1.

•

Portamento speed and on/of control are both set to MIDI CC 5.

•

Sustain pedal controls traditional sustain, and also latches notes into the
arpeggiator.

•

No scale or range tuning compensation.

Use the front panel buttons to change the configuration:

•

Press the Config button.

•

Scroll through the list of parameters with the Up and Down buttons. The

character will appear, indicating the value stored in memory.

•

To edit a parameter, hold the Config button down for 2 seconds. The

character will appear, indicating the Edit mode.

•

Scroll through the list of values with the Up and Down buttons.
Alternatively, turn or press MIDI controls, and the [KRM-100] will
automatically detect the correct MIDI CC for knobs, faders, etc.

•

Press the Config button to save the value, and exit the Edit mode.

•

Press the Config button again to exit.

All configuration changes are saved in non-volatile memory, and are retained
when power is removed from the [KRM-100].

The following is a full list of configuration parameters:

Configuration Parameters

MIDI CH

– MIDI Channel.

AUX CV CC

– MIDI CC for aux CV.

ARP ENBL CC

– MIDI CC toggle button for arpeggiator on/of.

ARP SPED CC

– MIDI CC for arpeggiator speed or MIDI beat quantization.

ARP GATE CC

– MIDI CC for arpeggiator gate percent.

ARP LTCH CC

– MIDI CC toggle button for arpeggiator latch (typically the

sustain pedal, or CC 64).

3 Changing the Default Configuration

Page 7

Содержание KRM-100


































Результаты поиска

Содержание KRM-100

Отзывы:

Бренды по названию

Популярные бренды

KRM KRM-100, Руководство пользователя

Результаты поиска

Содержание KRM-100

Отзывы:

Бренды по названию

Популярные бренды