Kramer VS-88UHD Скачать руководство пользователя страница 10

Страница: 10 / 78

Kramer Electronics Ltd.

VS-88UHD – Connecting the VS-88UHD

Connecting to VS-88UHD via RS-232

You can connect to the

VS-88UHD

via an RS-232 connection using, for example, a PC.

To connect to the

VS-88UHD

via RS-232:



Connect the RS-232 rear panel port on the

VS-88UHD

unit via a

9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 need to be

connected) to the RS-232 9-pin D-sub port on your PC.

Connecting VS-88UHD via the ETHERNET Port

You can connect to the

VS-88UHD

via Ethernet using either of the following methods:



Directly to the PC using a crossover cable (see

Connecting the Ethernet Port Directly to a

on page



Via a network hub, switch, or router, using a straight-through cable (see

Connecting the

Ethernet Port via a Network Hub or Switch

on page

If you want to connect via a router and your IT system is based on IPv6, speak to your IT

department for specific installation instructions

Connecting the Ethernet Port Directly to a PC

You can connect the Ethernet port of the

VS-88UHD

directly to the Ethernet port on your PC

using a crossover cable with RJ-45 connectors.

This type of connection is recommended for identifying the

VS-88UHD

with the factory configured default IP address.

After connecting the

VS-88UHD

to the Ethernet port, configure your PC as follows:

1. Click

Start

Control Panel

Network and Sharing Center

2. Click

Change Adapter Settings

3. Highlight the network adapter you want to use to connect to the device and click

Change

settings of this connection

The Local Area Connection Properties window for the selected network adapter appears

as shown in

Figure 4

Проконсультироваться

купить

данное

оборудование

вы

можете

компании

АНД

Системс

адрес

: 125480,

Москва

ул

Туристская

.33/1; site: https://andpro.ru

тел

: +7 (495) 545-4870 email: [email protected]

При

обращении

используйте

промокод

AND-PDF

получите

скидку

Содержание VS-88UHD















































































Результаты поиска

Содержание VS-88UHD

Отзывы:

Бренды по названию

Популярные бренды

Kramer VS-88UHD, Руководство пользователя

Результаты поиска

Содержание VS-88UHD

Отзывы:

Бренды по названию

Популярные бренды