background image

 

 

 

 

Kramer Electronics, Ltd. 

14 

LIMITATION OF IMPLIED WARRANTIES 

All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited 

in duration to the length of this warranty. 

EXCLUSION OF DAMAGES 

Kramer’s liability for any defective products is limited to the repair or replacement of the product at our option. 

Kramer shall not be liable for: 

1)  Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use 

of the product, loss of time, commercial loss; or: 

2)  Any  other  damages,  whether  incidental,  consequential  or  otherwise.  Some  countries  may  not  allow 

limitations  on  how  long  an  implied  warranty  lasts  and/or  do  not  allow  the  exclusion  or  limitation  of 

incidental or consequential damages, so the above limitations and exclusions may not apply to you. 

This  warranty  gives  you  specific  legal  rights,  and  you  may  also  have  other  rights,  which  vary  from  place  to 

place. 

 

 

NOTE

: All products returned to Kramer for service must have prior approval. This may be obtained from your 

dealer. 

 

 

 

 

 

NOTICE 

This equipment has been tested to determine compliance with the requirements of:  

 

EN-50081

"Electromagnetic compatibility (EMC); 
generic emission standard. 
Part 1: Residential, commercial and light industry" 

EN-50082

"Electromagnetic  compatibility  (EMC)  generic  immunity  standard.  Part  1: 

Residential, commercial and light industry environment". 

CFR-47

  

FCC Rules and Regulations:  

Part 15- “Radio frequency devices: 

Subpart B- Unintentional radiators 

 

CAUTION 

Servicing the machines can only be done by an authorized Kramer technician. Any user who makes 

changes or modifications to the unit without the express approval of the manufacturer will void user 

authority to operate the equipment. 
Use the supplied AC power cord (when applicable) to supply power to the machine and controllers. 
Please use recommended interconnect cables to connect the machine to controllers and other components. 

 

 

 

 

 

 

 

 

 

 

 

Содержание TOOLS 103YC


















Отзывы: