background image

3

PRODUCT FEATURES

SAFETY  DEVICE

A  standard  requirement for all vent-free  room
heaters.  This heater has a pilot  with  an  Oxygen
Depletion  Sensor(ODS)  safety  shutoff  system.
The ODS/pilot  shuts  off  the heater  if  there  is
not  enough  fresh  air.

PIEZO  IGNITION  SYSTEM

This  heater  is  equipped  with  a  piezo  ignitor.
This  system  requires  no  matches, batteries, or
other  sources  to  light  heater.

THERMOSTATIC  CONTROL  ON
THERMOSTAT   MODEL

These  heaters  have  a  control  valve  with  a
thermostat  sensing  bulb. This  results  in  the
greatest  heater  comfort  and  may  result  in
lower  gas  bills.

LOCAL  CODES

Install  and  use  heater  with  care. Follow  all  local
codes. In  the  absence  of  local  codes, use   the
latest  edition  of  

National  Fuel  Gas  Code  ANSZ223.1

,

also  known  as  NFPA  54*.
*Available  from :
        American  National  Standards Institute, Inc.

1430  Broadway

New York, NY 10018

National  Fire  Protection  Association, Inc.

Batterymarch  Park
Quincy, MA  02269

UNPACKING

1.   Remove  heater  from  carton.
2.  Remove  all  protective   packaging  applied  to

      heater  for  shipment.
3.   Check  heater  for  any  shipping  damage.  If  heater
     is damaged, promptly  inform  dealer  where  you
      bought  heater.

Figure1-Vent-Free  Propane/LP  Gas  Heater

Содержание KWP114






















Отзывы: