manualshive.com logo in svg

Kozy-World GFD4375KD, Руководство пользователя, Страница: 19 / 26

Поделиться
Скачать
Kozy-World GFD4375KD Скачать руководство пользователя страница 19

 

19 

 

  LIGHTING INSTRUCTIONS

    

 

                  
 

1. 

STOP! Read the safety information on the front and back of the warning plate on page 16. 

2. 

Make sure manual shutoff valve is fully open. 

3. 

Unscrew ignitor cap and install an AAA type battery with the anode (+) pointing out. Replace cap. 

4. 

Install two (2) AAA size batteries in the remote transmitter. 

5. 

Be sure the slide switch on the front of the receiver box is in the REMOTE position. 

6. 

Push in the control knob slightly and turn clockwise         to the OFF position. 

7.  Wait five (5) minutes to clear out out any gas. Then smell for gas around the heater and near the floor. If you 

smell gas, STOP! Follow "B" in the safety information on the rating plate. If you do not smell gas, go to the next 
step. 

8. 

Push the control knob in slightly and turn counterclockwise          to “PILOT” position and depress for five (5) seconds. 

Note

: The first time the heater is operated after connecting the gas supply, the control knob should be depressed 

for about thirty (30) seconds. This will allow gas to bleed from the gas system. 

9. 

With the control knob pushed in, push down and release the ignitor button.This will light the pilot. If needed, keep 
pressing the ignitor button until pilot lights. 

10.  Continue pushing the control knob in for an additional sixty (60) seconds to allow the thermocouple to warm up and 

to allow air to bleed from the gas system. Release the control knob.  

Note

: If the pilot goes out, repeat steps 7, 8, 9 and 10. 

11.  Rotate the control knob counterclockwise          to the ON position. 

12.  Press the LEARN BUTTON on the front of the remote receiver box until you hear a beep. 

13.  Press the ON button on the remote control transmitter to light the burner. (This will also “learn”, or program, the 

transmitter and the receiver).  

14.  If the transmitter is lost or damaged, the slide switch on the receiver can be used to operate the heater. 

 

   TO TURN OFF GAS TO APPLIANCE    

 

 

Shutting off heater 

 

1. Press the OFF button to let pilot stay. 

2. Turn gas control knob clockwise           to OFF position to shut off burner. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 16B - ON/OFF Switch location

Содержание GFD4375KD



























Отзывы:

Нет отзывов