background image

OPERATING INSTRUCTIONS 

25

WARNING

Do not operate appliance with the glass front removed, cracked, 
or broken. Replacement of the glass should be done by a licensed 
or qualiied service person.

Under no circumstances should any solid fuel (wood, coal, paper, 
cardboard, etc.) be used in this appliance.

Children and adults should be alerted to the hazards of high 
surface temperature and should stay away to avoid burns or 
clothing ignition.

CAUTION

Clothing or other lammable material should not be placed on or 
near the appliance.

Young children should be carefully supervised when they are in the 
same room as the appliance. Toddlers, young children and others 
may be susceptible to accidental contact burns. A physical barrier 
is recommended if there are at risk individuals in the house. To 
restrict access to a ireplace or stove, install an adjustable safety 
gate to keep toddler, young children and other at risk individuals 
out of the room and away from hot surfaces.

WARNING: 

If you do not follow these instructions exactly, a ire or explosion may result causing property damage, 

personal injury, or loss of life.

1. 

STOP! Read all the safety information above on this page. 

2. 

Press the wireless remote OFF button. 

3. 

Turn of all electric power to the appliance. 

4. 

This appliance is equipped with an ignition device which 
automatically lights the pilot. Do not try to light the pilot by 
hand.

5. 

Locate the manual valve installed by your qualiied service 
technician.

6. 

Turn the manual valve clockwise 

to the OFF position. 

7. 

Wait ive (5) minutes to clear out any gas. Then, smell 
for gas, including near the loor. If you smell gas, STOP! 
Follow ‘B’ in the safety information above. If you do not smell 
gas, go to the next step. 

8. 

Turn the manual valve counterclockwise  

to the ON 

position. 

9. 

Turn on all electric power to the appliance. 

10. 

Press the wireless remote ON button. 

11. 

If the appliance will not operate, follow the instructions, “To 
Turn Of Gas To Appliance” and call your service technician 
or gas supplier. 

OPERATING INSTRUCTIONS

NOTE

When this ireplace is initially lit, condensation will appear on the glass. This is normal in all gas ireplaces and will disappear after 
several minutes. A paint smell will occur during the irst few hours of burning. It is recommended to leave the fan of during this period to 
help speed the paint curing process. This ireplace may produce noises of varying degree as it heats and cools due to metal expansion 
and contraction. This is normal, and does not afect the performance or longevity of the ireplace.

A. 

This appliance is equipped with an ignition device which 
automatically lights the pilot. Do not try to light the pilot by 
hand. 

B. 

BEFORE OPERATING

 smell around the appliance area for 

gas. Be sure to smell next to the loor because some gas is 
heavier than air and will settle on the loor. 

WHAT TO DO IF YOU SMELL GAS
•  Do not try to light any appliance.
•  Do not touch any electric switch; do not use any phone 

in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions. 

•  If you cannot reach your gas supplier, call the ire 

department. 

C. 

Use only your hand to turn the gas control manual valve. 
Never use tools. If the valve will not turn by hand, do not 
try to repair it; call a qualiied service technician. Force or 
attempted repair may result in a ire or explosion. 

D. 

Do not use this appliance if any part has been under water. 
Immediately call a qualiied service technician to inspect the 
appliance and to replace any part of the control system and 
any gas control that has been under water. 

ON/OFF 

ON

OFF

1. 

Press the wireless remote OFF button.

2. 

Turn of all electric power to the appliance if service is to 
be performed. 

3. 

Locate the manual valve installed by your qualiied service 
technician.

4. 

Turn the manual valve clockwise 

to OFF position. 

FOR YOUR SAFETY READ BEFORE OPERATING

TO TURN OFF GAS TO APPLIANCE

11.0  OPERATING INSTRUCTIONS

Содержание CHASKA 29-ROCK CSK-29-R








































Отзывы: