kozy heat CALLAWAY ST Скачать руководство пользователя страница 63

Страница: 63 / 79

#CLW-ST R.1 February 2021

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

ELECTRICAL INFORMATION

9.4.1 Fan Channel Block-off Plate

If you wish to divert air from the fan so heated air exits to a certain

room, a block-off plate is included with the #CWST-028 fan kit for this

purpose. The block-off plate will be installed on the side you wish to

block air from exiting.

This is applicable to all design options. If using #CWST-ODK outdoor

kit, install the fan channel block off plate

BEFORE

installing the

#CWST-ODK. The block off plate cannot be placed on the interior side

so that hot air only exits to the exterior side.

1. Remove safety barrier screen, access cover, and front glass frame

assembly.

2. Locate the fan channel plates on the upper heat shield inside the

firebox. See Figure 9.5.

3. Remove fan channel plate you wish to block-off (2) screws.
4. Note the flange orientation on the block off plate, as shown

below. Install block-off plate with (2) screws previously removed.

5. Reinstall all components previously removed.

Figure 9.5, Fan Channel Block-off Plate Installation (shown from access side)

Remove fan channel plate

Install fan channel block-off plate

Содержание CALLAWAY ST
















































































Результаты поиска

Содержание CALLAWAY ST

Отзывы:

Бренды по названию

Популярные бренды

kozy heat CALLAWAY ST, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CALLAWAY ST

Отзывы:

Бренды по названию

Популярные бренды