4
4-1
Entering setting screen
The RPM input signal setting
4-3
The fuel resistance setting
4-2
The tire circumference
compensation setting
2 RPM signals per 1 spark.
1 RPM signal per 1 spark.
1 RPM signal per 2 sparks.
2 RPM signals per 10 sparks.
1 RPM signal per 3 sparks.
1 RPM signal per 4 sparks.
1 RPM signal per 6 sparks.
CAUTION!
1 piston
2 pistons
4 pistons
6 pistons
8 pistons
10 pistons
12 pistons
1 piston
2 pistons
3 pistons
4 pistons
6 pistons
0.5
1
2
3
4
5
6
NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
●
P.S.
NOTE
●
In main screen, press and hold the Select &
Adjust button for 3 seconds to enter the
setting screen.
The setting digit will flash!
Setting range: 0.5,1 ~24.
●
Then press the
Adjust button
to change
the setting value.
●
Press the
Select button
to enter the
sensor point setting.
●
Ex: To change the tire circumference setting
from 1000 mm to 1300 mm
.
●
Press the
Select button
to enter
the fuel resistance setting.
●
Ex.: To change the sensor point from
01P~06P.
The sensor point setting is flashing!
Setting range: 1~20 point.
●
Ex: To set the sensor point to 06P.
●
Press the
Adjust button
to change the setting.
●
EX. To connect the RPM signal wire to the
pick up signal and there are 13 flywheel
signals per turn.
●
Press the
Adjust button
to change the setting.
●
EX. Now the current input signal setting is 1.
wh642bb03b-P4-3
●
Press the
Select button once
to enter
the input pulse setting.
●
Ex. To change the RPM input signal number
setting from 1 to 13.
●
Press the Select button once to
enter the tire circumference compensation
setting.
●
EX.: To change the input pulse setting
from is Hi to Lo.
●
Ex.: To change the setting to Hi.
(The negative signal pulse.)
●
Press the
Adjust button
to choose
waveforms you would like to set.
Now the pulse setting is flashing!
We define the RPM input pulse as Hi (The
positive pulse) & Lo (The negative pulse.)
If the RPM displayed on the meter is
incorrect or with noise, please choose
another setting and try it again.
●
Keep pressing the
Select button once
to enter
the clock setting.
●
Ex.: To change the fuel resistance setting
from 100 to 510.
The fuel gauge resistance setting range:
100Ω
、
250Ω
、
510Ω
、
1200Ω
If you don’t install the fuel wiring, the fuel
gauge will not be displayed.
●
EX. The fuel gauge need to be set to 510Ω
●
Press the
Adjust button
to choose the setting
number.
When Fuel Resistance Setting is changed,
the remaining Mileage will be reset to 0 and have
to restart the learning process. About the Learning
process please refer to the instruction from 3-5.
For most of Injection Model, setting value might exceed 6 if RPM connection
method B is chosen, and it depend on the number of the bump it has on its flywheel.
●
Ex: The new tire circumference is 130 cm.
Use the equation below.
●
The new tire circumference ÷ the original tire
circumference X 100 = The value in %.
(130 ÷ 125 x 100 = 104%)
●
Press the
Select button
and release
it until it move to the setting digit you want.
●
Ex: The original setting is 1000
.
Now the setting digit value is flashing!
Setting range: 300~2500.
Setting unit: per 1 %.
Reset this setting value when you
change to a different tire size.
Setting
value
Most of the 4-cycle bikes with a single piston are igniting
every 360 degree, so the setting should be the same as the bike with
2-cycle and one piston engine.
2 strokes
setting
4 strokes
setting
RPM per spark
You can define the
valve as the starting
point and the terminal
point to measure the
wheel circumference
with a measuring tape.
