Korg M3, Руководство по параметрам

Страница: 451 / 647

Dynamics (Dynamic)
441
Dynamics (Dynamic)
000: No Effect
Select this option when you do not use any effects. The
Insert Effect/Total Effect section outputs unprocessed
signals and the Master Effect section mutes the output.
001: Stereo Compressor
This effect compresses the input signal to regulate the level
and give a “punchy” effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
a: Envelope Select
This parameter selects whether the left and right channels
are linked to control both signals simultaneously, or whether
each channel is controlled independently.
b: Sensitivity
g: Output Level
The Sensitivity parameter sets the sensitivity of the
compressor. If this parameter is set to a higher value, lower
level sounds will be boosted. With a higher Sensitivity, the
overall volume level is higher. To adjust the final volume
level, use the Output Level parameter.
c: Attack
This parameter controls the attack level.
002: Stereo Limiter
The Limiter regulates the input signal level. It is similar to
the Compressor, except that the Limiter compresses only
signals that exceed the specified level to lower unnecessary
peak signals. The Limiter applies a peaking-type EQ to the
trigger signal (which controls the degree of the Limiter
effect), allowing you to set any band width to be covered.
This effect is a stereo limiter. You can link left and right
channels, or use each channel individually.
a
Envelope
Select
L/R Mix,
L/R Individ-
ually Determines whether the left
and right channels are linked or
used separately
p.441
b Sensitivity 1...100 Sets the sensitivity p.441
c Attack 1...100 Sets the attack level p.441
d EQ Trim 0...100 Sets the EQ input level
e
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency
(low or mid-low) of the low-
range equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency
(high or mid-high) of the high-
range equalizer
f
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of the High EQ
g
Output Level 0...100
Sets the output level of the
compressor
p.441
Src Off...Tempo
Selects the modulation source
for the compressor output level
Amt –100...+100
Sets the modulation amount
for the compressor output level
h
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount
for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ HEQ
LEQ
HEQ
Compressor
Compressor
Envelope Select
Output Level
Output Level
Envelope - Control
Envelope - Control
a
Envelope
Source
Input,
FX Control 1,
FX Control 2 Selects the trigger source to
use: the input signal, FX Control
Bus 1, or FX Control Bus 2 p.442
FX Ctrl Trim 0...100
Sets the trigger input level from
FX Control Bus 1/2
b
Envelope
Select
L/R Mix,
L Only, R
Only, L/R
Individually
Selects from linking both
channels, controlling only from
left channel, only from the right
channel, or controlling each
channel individually
p.442
c Ratio
1.0 : 1…
50.0 : 1,
Inf : 1
Sets the signal compression
ratio
p.442
d
Threshold
[dB]
–40...0
Sets the level above which the
compressor is applied
p.442
e
Attack 1...100 Sets the attack time p.442
Release 1...100 Sets the release time p.442
f
Gain Adjust
[dB] –Inf,
–38...+24
Sets the output gain p.442
Src Off...Tempo
Selects the modulation source
for the output gain
Amt –63...+63
Sets the modulation amount of
the output gain
g
Side PEQ
Insert
Off, On
Toggles between on/off of the
trigger signal’s EQ
p.442
Trigger
Monitor
Off, On
Switches between effect
output monitor and trigger
signal monitor
p.442
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Left
Right
FX Control BUS 1
FX Control BUS 2
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Limiter
Limiter
Envelope Source
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+
Envelope Select