Korg M3, Руководство по параметрам

Страница: 110 / 647

Program mode
100
Effects must be chained in ascending numeric order. For
example, IFX1 can be chained to any of IFX2 through IFX5,
and IFX2 can be chained to IFX3 through IFX5.
You can chain two or more effects into the same down-
stream effect. For instance, both IFX1 and IFX2 can be
chained to IFX5.
Effects can also join a chain in the middle. For instance, you
can chain IFX3 to IFX4 to IFX5, and then chain IFX2 to IFX5
as well.
The Pan:#8, Bus Select, AUX/Ctrl Bus, and Send1/2
settings apply only to the last effect in the chain. However,
any effect in the chain can be sent to the FX Control buses.
IFX1: Chain [Off, On]
IFX2: Chain [Off, On]
IFX3: Chain [Off, On]
IFX4: Chain [Off, On]
This enables the chain, as set up by the Chain to parameter,
above.
Pan:#8:
Pan: #8 (Post IFX PanCC#8) [L000...C064...R127]
Specifies the panning immediately after the insert effect.
You can use CC#8 to control this.
Bus:
Bus (Bus Select) [Off, L/R, 1...4, 1/2, 3/4]
Specifies the bus to which the signal will be sent
immediately after the insert effect.
L/R:
The signal will be sent to the L/R bus, which passes
through TFX and then goes to the main L/R outputs. This is
the default setting.
1, 2, 3, 4: The signal will be sent, in mono, to the selected
individual output.
1/2, 3/4: The signal will be panned by the Pan: #8 setting, and
sent in stereo to the selected pair of audio outputs.
Off: The signal will not be sent directly to the outputs. This
setting is useful if you want to:
Use Send 1 or 2 to route the signal entirely through the
master effects, without sending the dry signal to the
outputs.
Use the FX Control Bus to route the signal to an effects side-
chain, such as a gate or vocoder, without being heard
directly at the outputs.
Use the AUX Bus to record the signal, without routing the
signal directly to the outputs.
AUX/Ctrl:
AUX (AUX Bus) [Off, 1, 2, 3, 4, 1/2, 3/4]
Sends the post-IFX signal to the AUX busses. For more
information, please see “AUX Bus” on page 98. If you want
to resample via the AUX busses, set the sampling Source
Bus
(Prog 0–7b) to AUX 1/2 or AUX 3/4.
Ctrl (FX Control Bus) [Off, 1, 2]
Sends the post-IFX signal to the FX Control busses. For more
information, please see “FX Control Bus” on page 98.
If you’re using Ctrl (FX Control Bus) as an input signal
for Vocoder etc., a feedback loop will occur if you
output to the same bus as specified here, and oscillation
will occur. Set this with care to avoid creating a loop.
Send1/2:
Send1 [000...127]
Send2 [000...127]
These adjust the level at which the post-IFX signal is sent to
master effects 1 and 2. This is valid if Bus (Bus Select) (Prog
8–2a) is set to L/R or Off.
You can use CC#93 to control the Send 1 level, and
CC#91 to control the Send 2 level. The global MIDI
channel specified by MIDI Channel (Global 1–1a) is
used for these messages.
▼
8–2: Menu Command
• 0: Write Program
☞
p.106
• 1: Panel–SW Solo Mode On
☞
p.106
• 2: Exclusive Solo
☞
p.107
• 3: Copy Insert Effect
☞
p.117
• 4: Swap Insert Effect
☞
p.118
For more information, please see “Program: Menu
Command” on page 106.