Korg Electronic Keyboard, Руководство по параметрам

Страница: 156 / 1127

Program mode: HD-1
146
This option is available only when the
Oscillator
Mode
is set to
Double
.
1. Select “Sync Both EGs.”
The LCD screen will indicate “Sync Both EGs,” and
the two EGs will be synchronized.
2. If you no longer want the EGs to be synchronized,
select “Sync Both EGs” once again.
The indication will disappear from the LCD screen.
Swap LFO 1&2
Swap LFO 1 & 2
is available on all of the LFO pages,
except for the Common LFO tab.
This command copies the settings of LFO1 to LFO2,
and vice-versa.
Note: If LFO2 is being used to modulate LFO1, this
command will erase that modulation routing (since the
LFOs cannot modulate themselves).
After opening the dialog box, press the OK button to
swap the LFO settings, or press the Cancel button to
close the dialog box without making any changes.
Copy KARMA Module
Copy KARMA Module
is available on all of the
KARMA pages, as well as the KARMA GE tab of the
Play page.
This command copies the settings of the KARMA
Module used by a specified program, combination, or
song.
1. Select “Copy KARMA Module” to open the dialog
box.
2. In “From,” select the copy source mode, bank, and
number.
You can use the front panel BANK SELECT switches to
select the bank.
3. If you selected a combination or song as the copy-
source, select the module from which you want to
copy.
4. As appropriate for the content that you want to
copy, turn “GE RTP Control Setting & Scenes” On
(checked).
For more information, see “Settings copied by “Copy
KARMA Module”,” below.
5. If you want to copy performance realtime
parameters, Dynamic MIDI, and front panel
settings, turn “Perf. RTP & Panel Settings” On
(checked).
6. If you want to copy the note and velocity settings
of pads 1–8, turn “Pads” on.
7. Press the OK button to execute the Copy KARMA
Module command, or press the Cancel button if
you decide to cancel.
Settings copied by “Copy KARMA Module”
When copying from a program
If “GE RTP Control Setting & Scenes” and “Perf. RTP &
Panel Settings” are Off (checked), the following
content is copied.
•The GE selected by the copy-source KARMA
module.
•Settings of the KARMA module parameters (7–3:
Module Parameter-Trigger, 7–4: Module
Parameter-Control).
•7–5: GE RTP page “MIN,” “MAX,” and “VALUE”
settings.
If you turn “GE RTP Control Setting & Scenes”
On (checked)
In addition to the content copied when “GE RTP
Control Setting & Scenes” is Off (unchecked), the
following content is copied.
•7–5: GE RTP page “ASSIGN” and “POLARITY”
settings.
•The scene selected in the master buffer, the
KARMA CONTROLS slider and KARMA
SWITCH settings of each scene (0–6d: Realtime
Controls and 0–9f: R.Time Knobs/KARMA
settings).
•7–8: Name/Note Map controller name settings.
If you turn “Perf. RTP & Panel Setting” On
(checked)
In addition to the content copied when “Perf. RTP &
Panel Settings” is Off (unchecked), the following
content is copied.
•“Tempo” setting.
•“Time Signature” setting.
•KARMA ON/OFF switch setting.
•KARMA LATCH switch setting.
•7–6: Perf Real– Time Parameters page settings.
•7–7: Dynamic MIDI page settings.
When copying from a combination or song
If “GE RTP Control Setting & Scenes” and “Perf. RTP &
Panel Settings” are Off (unchecked) when you copy
from a combination or song, the following content is
copied.
•The GE selected for the copy-destination KARMA
module (including the GE realtime parameters).
•KARMA module parameters (7–3: Module
Parameter-Trigger, 7–4: Module Parameter-
Control).
•7–5: GE RTP page “MIN,” “MAX,” and “VALUE”
settings.
If you turn “GE RTP Control Setting & Scenes”
On (checked)